Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This authentic replacement blade is manufactured for use with Craftsman walk-behind lawnmowers and is designed to deliver clean, efficient cuts. Measuring 21 inches in length, the blade features an an...
This spark plug is designed to provide reliable ignition and efficient fuel combustion in small engine applications. Built for consistent performance and durability, it helps maintain smooth operation...
This trail shield, also referred to as a rear skirt, is designed for use with various makes and models of lawn mowers and is a genuine OEM part. This trail shield is sold as an individual part without...
This is an original manufacturer-approved replacement part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. Its purpose is to filte...
The Blade Support (Bell Blade Support) fits between the bottom of the blade and the blade bolt to provide support for the blade. It is installed underneath the cutting deck on the blade. Installation ...
This replacement screw is a genuine item that is sourced from original equipment manufacturer. It is a high quality hardware that is commonly used with walk-behind lawn mowers. This screw has multiple...
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should ...
This screw is an authentic Briggs and Stratton replacement part. It is compatible with and commonly used in over 150 models of engines. This screw has multiple functions varying from machine to machin...
Also referred to as a Lock Nut or Flange Lock, this nut is designed for use with various lawn and garden equipment. The purpose of this part is to hold parts in place while resisting loosening when pr...
The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of meta...
$6.40
In Stock
Order now and your part arrives by May 29
Questions And Answers for 11B-B28S799
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
This was an OHV motor so in order to get to the head, you must remove the valve cover and remove the push rods. Remove all four head bolts in an even star pattern. Remove the old gasket and scrape all remaining gasket gunk. Put new gasket on and tighten head back on with an even star pattern. Slide push rods back in and adjust valves to .
... Read more004 of an inch and put valve cover back on and start it up!
Remove the top cover and pull cord assembly. Remove the muffler cover. Lift off the gas tank and disconnect from the air filter box. Remove the air filter box and carb from the head cover as a single unit. Remove the head cover. You can leave the valve cover in place. Remove old gasket material. Clean surfaces. Replace gasket. Reassemble
... Read more. *if the valve stems come loose from their seats or rockers, remove the valve cover and reseat. Reassembly is the opposite of disassembly. Happy mowing.
