11061402311 Kenmore Dryer - Overview
Sections of the 11061402311
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Heating Element - 240V 5400W
PartSelect #: PS334313
Manufacturer #: 279838
The heating element (Flat Can Heating Element 5400W, Heating Element, Whirlpool Dryer Heating Element, Dryer Heating Element) provides heat to the dryer. It is metal and measures 10.5 inches long, 7.5...
$57.07
In Stock
Dryer Cycling Thermostat
PartSelect #: PS11741405
Manufacturer #: WP3387134
This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heate...
$26.20
In Stock
Thermal Cut-Off Kit
PartSelect #: PS334299
Manufacturer #: 279816
The thermal cut-off (Dryer Thermal Cut-Off Fuse Kit, Dryer Thermal Cut-Off Kit) prevents the dryer from overheating when the dryer high limit thermostat fails in a closed circuit condition. This part ...
$46.30
In Stock
Maintenance Kit
PartSelect #: PS373087
Manufacturer #: 4392065
The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt att...
$34.97
In Stock
Rear Drum Support Roller Kit
PartSelect #: PS347627
Manufacturer #: 349241T
The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings, and one palnut (or retaining washer). The kit does n...
$17.80
In Stock
Dryer High Limit Thermostat
PartSelect #: PS11742185
Manufacturer #: WP3977767
A dryer high-limit thermostat (High Limit Thermostat, Hi-Limit Thermostat, Dryer High-Limit Thermostat) is a switch that is actuated by temperature change. This high limit thermostat acts as a safety ...
$19.90
In Stock
Dryer Idler Pulley Assembly
PartSelect #: PS11743765
Manufacturer #: WP691366
This part provides the tension required for a multi-ribbed belt. It also helps the belt rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long t...
$15.70
In Stock
Roller Support Tri-Ring
PartSelect #: PS11755850
Manufacturer #: WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$11.50
In Stock
Heating Element Connection Wire Kit
PartSelect #: PS334206
Manufacturer #: 279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
$9.40
In Stock
Rear Drum Felt Seal
PartSelect #: PS8691753
Manufacturer #: W10612022
This is a genuine OEM replacement rear drum seal for your dryer. This seal is made of felt and comes with the adhesive required for installation. The purpose of the seal is to prevent hot air from esc...
$41.15
In Stock
Dryer Screw
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.30
In Stock
Dryer Blower wheel
PartSelect #: PS11743785
Manufacturer #: WP694089
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
$33.94
In Stock
Questions And Answers for 11061402311
Ask our experts a question about this model and we'll get back to you as soon as possible!
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
LINDSEY
November 29, 2019
My dryer do not get hot so do i just need to buy the thermal fuse
For model number 11061402311
Hello LINDSEY and thanks for writing.
There are several parts that could cause this. Most likely your
Your thermal cut of fuse # PS334299, next the cycling thermostat # PS11741405, next the high limit thermostat # PS11742185 We hope this helps. Please contact us anytime.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Charles
February 15, 2023
Dryer doesn't heat up
For model number 11061402311
Hello Charles, thank you for reaching out. We looked into your model and found that this issue indicates that there may be a problem with the heating element or a blown thermal fuse. We found the exact-fit parts: Heating Element (Part number: PS334313), and Thermal Cut-Off Kit (Part number: PS334299). If this will not solve your problem then you may have to replace Dryer Cycling Thermostat (Part number: PS11741405). We hope it will solve your problem.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Steve
March 25, 2024
My dryer runs fine and the heat is working. But there is no air running through the vent. I took the back panel off and could see that the fan is not running. Is the motor bad ? Thanks..
For model number 11061402311
Hi Steve, thank you for reaching out. Based on our research, we would recommend checking the blower wheel if it is stuck or damaged. If that is not the case, then you probably have a defective drive motor, part number PS334304, and needs to be replaced to fix the issue. We hope this solves your problem!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Kevin
November 21, 2025
Need leveling feet
For model number 11061402311
Hi Kevin, thank you for reaching out. The leveling feet for your model are part number PS1609293. These are sold individually. We hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Common Symptoms of the 11061402311
[Viewing 9 of 9]Noisy
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Heat stays on after drum has stopped
Fixed by
these parts
these parts
Show All
Timer Not Working
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer motor runs, but no heat
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element wi ... Read more th an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
Good luck.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element wi ... Read more th an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
Good luck.
Read less
Parts Used:
-
Gadi from Irvine, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
2299 of 2491 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Heat
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back
... Read more
off.
Read less
Parts Used:
-
Vernon from Niceville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
901 of 967 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would run with no heat.
The repair was easy. the most time consuming part was vacuuming the dust from the back of the Dryer, The repair required removing screw from the back panel of the dryer. Then removing screws from the heating element and unplugging the wires. The only moderately diffculy part was swapping the sensor form the old element.
Parts Used:
-
Remie from Mahopac, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
730 of 762 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!