Models > 11026912691

11026912691 Kenmore Washer - Overview

Sections of the 11026912691

[Viewing 9 of 9]

Manuals & Care Guides for 11026912691

Click to download
Keep searches simple, eg. "belt" or "pump".
Agitator Directional Cogs – Part Number: 80040
Agitator Directional Cogs
★★★★★
★★★★★
(359)
PartSelect #: PS388034
Manufacturer #: 80040
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your wa...
$4.39
  In Stock
Direct Drive Motor Coupling – Part Number: 285753A
Direct Drive Motor Coupling
★★★★★
★★★★★
(160)
PartSelect #: PS1485646
Manufacturer #: 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft....
$27.84
  In Stock
Direct Drive Water Pump – Part Number: WP3363394
Direct Drive Water Pump
★★★★★
★★★★★
(101)
PartSelect #: PS11741239
Manufacturer #: WP3363394
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is ...
$48.71
  In Stock
Suspension Spring – Part Number: WP63907
Suspension Spring
★★★★★
★★★★★
(27)
PartSelect #: PS11743345
Manufacturer #: WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
$8.00
  In Stock
Water Inlet Valve with Mounting Bracket – Part Number: 285805
Water Inlet Valve with Mounting Bracket
★★★★★
★★★★★
(134)
PartSelect #: PS334646
Manufacturer #: 285805
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There...
$35.25
  In Stock
Clutch Assembly – Part Number: 285785
Clutch Assembly
★★★★★
★★★★★
(78)
PartSelect #: PS334641
Manufacturer #: 285785
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining ...
$27.55
  In Stock
Lid Switch Assembly – Part Number: WP3949238
Lid Switch Assembly
★★★★★
★★★★★
(89)
PartSelect #: PS11742021
Manufacturer #: WP3949238
This part comes with a three-wire lead. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
$51.82
  In Stock
Tub Spring – Part Number: WPW10250667
Tub Spring
★★★★★
★★★★★
(18)
PartSelect #: PS11751118
Manufacturer #: WPW10250667
This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front...
$7.03
  In Stock
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.41
  In Stock
Tub Wear Pads - Package of 3 – Part Number: 285744
Tub Wear Pads - Package of 3
★★★★★
★★★★★
(8)
PartSelect #: PS334620
Manufacturer #: 285744
This package of pads contains three tub wear pads.
$16.83
  In Stock
Hose Clamp – Part Number: WP596669
Hose Clamp
★★★★★
★★★★★
(1)
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.77
  In Stock
Leveling Spring – Part Number: 8316845
Leveling Spring
★★★★★
★★★★★
(7)
PartSelect #: PS394983
Manufacturer #: 8316845
This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.
$11.13
  In Stock

Questions And Answers for 11026912691

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

4 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
November 29, 2019
Replaced water pump but water will not drain from washer, the dial stops before it will drain
For model number 11026912691
PartSelect logo
Hello David and thanks for writing. There are several culprits that cause slow or stopped washing machine drains. ... A kink or bend in the hose slows the drain down. An improperly attached hose or pump also causes problems. Draining standing water, before it starts to mildew or smell stale, is a messy but straightforward task. Also check the lid switch #PS11742021. You can also, refer to the manual troubleshooting section on our website for your model. We hope this helps. Please contact us anytime.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Tim
January 27, 2023
Hi, thnx for ur help. I suspect my agitator dogs need replacement. Ever video I've watched shows a 7/16 bolt secures the top agitator to the drive train. Mine doesn't have that. It looks like a WHT plastic slotted stepped retainer that's got and internal thread in the middle with a square hole molded into it that looks like it takes either a 3/8 or 1/2 socket driver. My question is: is this a retaining nut that I would unscrew to remove the top agitator in lieu of the bolt that is shown in all the repair videos? Thnx a lot. Regards, Tim
For model number 11026912691
PartSelect logo
Hello Tim, thank you for reaching out. Yes, in your model there is a plastic retainer that holds the agitator cam kit. Unscrewing this retainer will free your agitator cam kit and separate your upper agitator from the lower agitator. We hope this solves your problem!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Larry
April 19, 2023
Technique to separate the top cover from the tube Shell. Does the starting capacitor on the Moter fail an let the washer stop before a cycle is complete?
For model number 11026912691
PartSelect logo
Hello Larry, thank you for the question. You will need to first remove the control panel from the plastic casing on its side and unscrew the screws under it. After removing the panel, press the clips under the panel on the washer body to remove the top assembly. Using a screwdriver, press all the clips on the tub's plastic ring and remove the plastic ring body from the top of the tub. Yes, a faulty capacitor can cause the motor to stop functioning, and the cycle does not get completed. In that case, you may need to replace the start capacitor, part number PS11746661. We hope this helps.

Was this helpful?
Thank you for voting!
Related Parts:
Dean
March 22, 2024
Makes loud knocking when in the spin cycle. Tub does spin
For model number 11026912691
PartSelect logo
Hi Dean, thank you for getting in touch. Based on our research, the issue is with the clutch kit, part number PS334641. It spins the basket during the spin cycle. You may need to replace it to fix the issue. Good luck with your repair!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1

Common Symptoms of the 11026912691

[Viewing 17 of 17]
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Burning smell
Fixed by
these parts
Fixing Fixing
Show All
Spinning Issues
Fixed by
these parts
Fixing Fixing Fixing
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
Fixing Fixing
Show All
Shaking and Moving
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaks water
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing
Show All
Water Filling Issues
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing Fixing
Show All
Not cleaning dishes properly
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Touchpad does not respond
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Parts Used:
Direct Drive Motor Coupling
  • Jeff from Wayne, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
1092 of 1176 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Parts Used:
Agitator Directional Cogs
  • mike from Kent, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
931 of 1011 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace Water Pump Coupling
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump.
Parts Used:
Tub Spring Direct Drive Water Pump Bleach Dispenser - White
  • RICHARD from PHILA, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench set
838 of 904 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!