10RJ37C Hotpoint Range - Overview
Sections of the 10RJ37C
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Bake Element
PartSelect #: PS249449
Manufacturer #: WB44X5043
The GE Appliances Bake Element is a top-quality replacement part designed specifically for electric ovens. Located at the bottom of the oven, it provides the necessary heat for baking. Its installatio...
$58.73
In Stock
Silicone Door Gasket
PartSelect #: PS242422
Manufacturer #: WB2X5103
This gasket seals the oven/range door.
No Longer Available
Standard Single Hydraulic Range Thermostat
PartSelect #: PS235958
Manufacturer #: WB21X5210
This standard single range hydraulic thermostat is used with some of GE's brands of ranges and ovens. The length of this thermostat's capillary is 34 inches.
No Longer Available
Common Symptoms of the 10RJ37C
[Viewing 2 of 2]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven's bottom bake element burned up
First I turned the circuit breaker switch off for the stove unit. I then removed the two screws that hold the element in place at the back of the oven. I then pulled the element out about 3 inches and disconnected the two wires. I attached the new element, bolting the wires into place and then screwed the element back into place on the
... Read more
back wall of the oven. I flipped the breaker switch back on, and turned on the oven. I was done in roughly 15 minutes. The most difficult part was having to shine a flash light into the oven to replace the part, and negotiating the hard cold kitchen floor.
Read less
Parts Used:
-
Dennis from Los Alamos, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
19 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven element burned completely into.
I first removed the two screws holding the element in place. Then I pulled the element out about 2 or 3 inches and then took out the 2 small screws holding the 2 wires in place. I then removed the old element and discarded it and installed the new one in the reverse order that I took out the old one. It was quite easy to do, only took abo
... Read more
ut 10 to 15 minutes total time.
Read less
Parts Used:
-
John from Kiowa, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old gasket (seal) broken and leaking
The oven is 70 years old and used several times a week so getting it to come apart wasn't working.
Used a light oil and some thinner to work loose the old seal, which was stuck pretty good, removed it by lightly prying the seal lip wider and pulling it out, mostly piece by piece. The worked in the new one and became of the light ... Read more oil, it went in rather easy. Had to trim an inch or so from each end and wiped down and cleaned up. No more problems....
Used a light oil and some thinner to work loose the old seal, which was stuck pretty good, removed it by lightly prying the seal lip wider and pulling it out, mostly piece by piece. The worked in the new one and became of the light ... Read more oil, it went in rather easy. Had to trim an inch or so from each end and wiped down and cleaned up. No more problems....
Read less
Parts Used:
-
William from SAN DIEGO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!