Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
Frequently referred to as a Drain Plug, this Drain Valve is used to drain any condensation that has collected inside the tank to prevent the tank from rusting. It is not part of a kit or assembly, is ...
This is an authentic part that is supplied directly from the original equipment manufacturer for use with Craftsman Air Compressors. The exhaust flapper valve attaches on the valve plate under the cyl...
This is an authentic OEM sourced item that is specially designed for use with Craftsman air compressors. It is an identical replacement for a missing or worn belt that drives the unit, please make sur...
This part is an OEM from Campbell Hausfeld for use with air compressors. The air filter cleans the air entering the air compressor. The most common reason for replacing the filter is if it is dirty. T...
This handle is an original replacement part supplied by the manufacturer. It is commonly used in Campbell Hausfeld air compressors. It is compatible with over 150 models. This handle is attached to th...
This is the genuine OEM supplied replacement part that is used on Campbell Hausfeld air compressors. A gasket is a mechanical seal which fills the space between the cylinder and the cylinder head. It ...
This is an OEM part sourced directly from the manufacturer. The screw is commonly found in Craftsman compressors and paint sprayers. This part is made of metal, and is generally used to secure the f...
This is an authentic manufacturer sourced replacement part which is specially designed for use with Campbell Hausfeld Air Compressors. The purpose of the oil seal is to prevent oil from leaking betwee...
This is a genuine OEM part. The compression connector assembly is made by Campbell Hausfeld, and is compatible with many air compressor devices. The metal component secures the manifold to the compres...
This is a genuine replacement part sourced directly from the manufacturer. The gasket is commonly found in Craftsman air compressors and paint sprayers. This part is made of flexible plastic, and is...
This is an authentic part is sourced directly from the original equipment manufacturer. The bearing cap gasket is commonly found in Craftsman air compressors. The purpose of this component is to provi...
$10.90
In Stock
Order now and your part arrives by Mar 19
Questions And Answers for 106153784
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the guard and belt. Heated the flywheel with a propane torch. Careful not to over heat it. Flywheel came off easily with a 3 point puller. Removed the cap and pulled the old seal out. Cleaned the bore in the cap to get all the oil out and dried it. Started the seal into the cap with the letters out. Carefully pushed the seal down
... Read moreinto the bottom of the cap with a long socket slightly smaller than the bore. Put a little oil on the inside of the seal and put the cap back on. Reheated the flywheel somewhat again and tapped it back on the shaft with a brass drift. Put the belt and guard back on. Started the compressor. No more oil leaking around the shaft.
TURN OFF POWER TO UNIT REMOVE BOLTS ON TOP SIDE OF COMPRESSOR PUMP TO REMOVE PLATE. THERE ARE 2 SMALLER PLATES THAT COVER FLAPPER W/ 2 SMALL SCREWS ON EACH (MAKE NOTE OF SMALL TOP PLATE POSITION) REPLACE FLAPPER AND REASSEMBLE. THERE IS A GASKET ON LARGER PLATE THAT MAY NEED TO BE REPLACED.
