030247-1 Generator - Overview
Models starting with 030247-1
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
Fuel Gauge Cap
PartSelect #: PS9314364
Manufacturer #: B4363GS
This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It i...
$58.31
On Order
Line-fuel
PartSelect #: PS9140673
Manufacturer #: 791745
This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to tra...
$16.54
On Order
Solenoid
PartSelect #: PS9064363
Manufacturer #: 691656
A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acti...
$35.85
On Order
Voltage Regulator
PartSelect #: PS9270265
Manufacturer #: 205858GS
The OEM voltage regulator or voltage control is a part used to regulate the voltage so it can provide the right amount of power to electrical components. It attaches inside the alternator housing. The...
$141.49
In Stock
Breaker, Circuit, 20a
PartSelect #: PS9919917
Manufacturer #: 209872GS
This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the elec...
$15.46
In Stock
E-ring
PartSelect #: PS10000220
Manufacturer #: 703977
The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.
$6.73
In Stock
Battery
PartSelect #: PS8906971
Manufacturer #: 193463GS
This Battery supplies power to a generator's electrical systems. It attaches inside the battery housing, which is usually mounted to the frame. It can be installed using a wrench set, and its installa...
$197.14
Special Order
Assembly, Holder, Brush
PartSelect #: PS9063496
Manufacturer #: 66386GS
The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached spri...
$32.55
In Stock
18oz 30w 4 Cycle Oil
PartSelect #: PS8817222
Manufacturer #: 100005
This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This...
$10.39
In Stock
Wheel
PartSelect #: PS8914298
Manufacturer #: 209636GS
The authentic 10" Wheel Assembly (Wheel, 10" Diameter) is a 10-inch black, plastic-and-ubber wheel. It allows easy moving of the generator. Installation requires pliers and is rated as "Easy". If your...
$113.48
In Stock
Brkr Crct 30a 2p
PartSelect #: PS9269236
Manufacturer #: 192785GS
This is an authentic Briggs & Stratton replacement part that is sourced from the original manufacturer for use with generators. The circuit breaker attaches to the compact control panel. During replac...
$129.10
Special Order
Common Symptoms of models starting with 030247-1
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn’t start.
I installed a new solenoid starter. Took me a total of 20 minutes. Started right up.
Parts Used:
-
Bruce from CARNATION, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
15 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!