Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
01421-0 Briggs and Stratton Pressure Washer - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
Used to connect the hose that supplies the chemical cleaning solution (soap), this OEM replacement Chemical Injection Kit consists of the brass fittings, a metal ball, a spring, and a rubber seal, and...
This filter, also known as a water inlet screen, is designed for use with pressure washers and has a 1-inch diameter (including the surrounding rubber housing). The filter itself is made of mesh and i...
This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment...
This replacement part is used on the base of various models of pressure washers to reduce vibration from the pump. This Grommet has an O.D. of 1 inch, is not part of a kit or assembly, is sold individ...
It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton generators and pressure washers. The purpose of this component is to reduce the...
The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or da...
This is an authentic component is sourced directly from the original equipment manufacturer. It is the part that is specially made for use with Briggs and Stratton and Snapper pressure washers. The pu...
This Chemical Hose Filter is a genuine replacement part for various models of pressure washers. It is made of durable blue plastic, is not part of a kit or assembly, is sold individually, and is used ...
This is a genuine OEM sourced component that is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is designed to keep the fuel in the tank...
$33.20
In Stock
Order now and your part arrives by Mar 19
Questions And Answers for 01421-0
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I order the part from this site and received it within a week. the only problem was that spring was missing out of the sealed bag. NO PROBLEM!!! I cut a ball point pen spring to fit and everything works just fine. You just have to remember to put the spring in first, then the ball bearing and then the rubber o-ring.If you put them in back
... Read morewards you pressure will fed directly into your chemical container!!
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read morer /> used same technique to insert valve upward into bushing
