Campbell Hausfeld Parts

Campbell Hausfeld Regulator This is a genuine Campbell Hausfeld replacement part designed for use with air compressors. It is used to regulate the air pressure in the compressor tank. It is also used to regulate the air pressure of the air exiting the tank. In some instances you will need to lower or higher the air pressure of the tank and the air coming from the tank. It is made out of metal with a plastic knob. This regulator is sold individually. To complete this repair you would need a set of wrenches.

Campbell Hausfeld Svc Compressor Pump Cw 75 X 51mm Svc Compressor Pump Cw 75 X 51Mm

Campbell Hausfeld Ferrule Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

Campbell Hausfeld Pressure Switch Authentic Campbell Hausfeld replacement part designed to work with Campbell Hausfeld Air Compressors. The pressure switch tells your compressor when to stop and when to start. There are multiple reasons a Pressure Switch could be leaking air. If it is leaking air the Pressure Switch should be replaced for a compressor to operate properly and safely.

Campbell Hausfeld Drain Valve This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to drain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

Campbell Hausfeld Pres Ga 250psi Sd Mnt Nochlogo The purpose of a gauge is to register the pressure readings inside the tank. This replacement gauge is sourced directly from original equipment manufacturer for use with Campbell Hausfeld air compressors. The dial reads 0-250 PSI. Please note this gauge has a durable metal body and it is sold individually. You should only need a wrench and a thread-sealing tape to complete this repair.

Campbell Hausfeld Air Filter Element This is a genuine OEM sourced replacement part used on Campbell Hausfeld air compressors. Its purpose is to filter out dust and debris from contaminating the engine. This filter is made out of paper and metal. This item is sold individually. To replace this you would need a wrench to remove the air cleaner cover.

Campbell Hausfeld Pressure Switch This is an authentic replacement part manufactured for use with Campbell Hausfeld pressure washers. The pressure switch is used to turn the pump on or off depending on the amount of air pressure within the tank. A faulty switch will likely prevent the pump from turning on when the pressure in the tank is low. This switch is available as an individual replacement part, please see model diagram for associative parts.

Campbell Hausfeld Belt This is a genuine OEM approved replacement drive belt. It is supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the belt that connects the pump and the electric motor. Over time these rubber belts tend to wear out and stretch eventually requiring replacement to maintain peak performance. Always make sure to clean the pulleys before installing the new belt, this will help to ensure longevity of the new belt. Includes one (1) belt per order. Replacing this belt is a very simple task that should only require a screwdriver. • Make sure to unplug the compressor and drain the tank • Remove the cover screws • Separate the cover from the unit • Remove the old belt • Clean the pulleys • Install the new belt • Secure the cover with the screws

Campbell Hausfeld Check Valve This OEM Check Valve is an exact replacement for certain air compressors. The purpose of this part is to allow pressurized air into the tank and stop it from flowing back into the pump. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. When the check valve is defective, the compressor will funcyion normally until the tank fills with air. At that point, the pump will try to restart, but the engine will only produce a humming noise. Similarly, if the tank is full of air, the motor will make a humming noise without engaging. This part is located on the tank to the discharge tube and will need to be replaced if broken or worn. You will need a wrench set and a socket set to complete this repair. Customers rate this repair as Easy.