Ariens Lawn Tractor Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Ariens Lawn Tractor Hardware
Your Price
$6.72
In Stock
Ariens Lawn Tractor Washer Head Screw
PartSelect Number PS9982804
Manufacturer Part Number 584953901
This part is the replacement washer head screw for your lawn tractor. It is black in color and is approximately an inch and a half in length. This self-threading screw is most commonly used for securing the mandrel housing to the mower deck of your lawn tractor. The main reason you would need to replace this part is if the old screw is damaged or missing. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
Your Price
$6.72
In Stock
Ariens Lawn Tractor Lawn Mower Ring Clip
PartSelect Number PS9143890
Manufacturer Part Number 812000029
The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle.
This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.
Installation Instructions
Anthony from OLIVEHILL, TN
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Read more...
Your Price
$7.39
In Stock
Ariens Lawn Tractor Lawn Mower Mandrel Spacer Washer
PartSelect Number PS9286886
Manufacturer Part Number 532187690
An OEM part sourced directly from the manufacturer, this part is sold individually. Washers help to spread the load, and prevent damage to the surface being fixed, or provide some sort of insulation such as electrical. Washers can also be important for preventing galvanic corrosion. This specific washer is commonly used with outdoor lawn equipment, and is compatible with the mowers and tractors that are listed below.
Your Price
$13.44
In Stock
Ariens Lawn Tractor Bolt And Washer Assembly
PartSelect Number PS9020856
Manufacturer Part Number 532193003
This manufacturer-approved bolt and washer assembly is for lawn tractors.
Wear work gloves to protect your hands when installing this part.
Your Price
$6.72
In Stock
Ariens Lawn Tractor Lawn Mower Washer
PartSelect Number PS9008998
Manufacturer Part Number 532121749
This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number to confirm this is the washer you need for your equipment.
This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.
Installation Instructions
Frederick from BINGHAMTON, NY
Your Price
$6.72
In Stock
Ariens Lawn Tractor Lawn Mower Hardened Washer
PartSelect Number PS9015920
Manufacturer Part Number 532188967
This OEM hardened washer spreads load under the bolts of your lawn tractor. It is silver, made of metal, and is sold individually. Over time, the washer may become damaged due to wear and fatigue, and will need to be replaced. You may notice this part is damaged if you start hearing a grinding or rubbing noise between the tire rim and ring clip.
You will need a pair of needle nose pliers to carry out this repair, which our customers generally found easy.
You will locate the washer on the spindle, between the wheel and the ring clip.
Your Price
$6.72
In Stock
Ariens Lawn Tractor Lawn Mower Flangelock Hex Nut
PartSelect Number PS9022497
Manufacturer Part Number 532409149
Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To replace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.
Your Price
$6.72
In Stock
Ariens Lawn Tractor Flange Top Lock Nut
PartSelect Number PS16381821
Manufacturer Part Number 596134801
This high-quality item is an authentic OEM hardware that is designed for use with Craftsman riding lawn mowers and garden tractors. It is one of the locknuts that is utilized to secure the pulleys. A locknut is a nut that resists loosening under vibration and torque. Refer to the diagrams of your model for the exact location and the correct application of this part. One durable metal locknut is included. You will need a wrench to secure and remove it.
Your Price
$6.72
In Stock
Ariens Lawn Tractor Washer 5/16 Std Flt
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
PartSelect Number PS16381824
Manufacturer Part Number 596134901
It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tight seal between connected parts, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this durable metal washer is sold individually.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair. HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Your Price
$6.72
In Stock
Ariens Lawn Tractor Bowtie Cotter Pin
PartSelect Number PS9020881
Manufacturer Part Number 532194209
This is a Genuine Manufacturer Sourced replacement part used on a Riding Lawn Mowers/Tractors. This part is made out of Metal and it is Sold Individually. These pins anchor various assemblies by insertion through a drilled hole in a shaft or bolt and then spread the points to hold the assembly into position.
Related Ariens Lawn Tractor Parts
- Ariens Lawn Tractor Bearings
- Ariens Lawn Tractor Belts
- Ariens Lawn Tractor Blades
- Ariens Lawn Tractor Brackets and Flanges
- Ariens Lawn Tractor Caps and Lids
- Ariens Lawn Tractor Carburetors
- Ariens Lawn Tractor Circuit Boards and Touch Pads
- Ariens Lawn Tractor Control Cables
- Ariens Lawn Tractor Deflectors and Chutes
- Ariens Lawn Tractor Engines
- Ariens Lawn Tractor Exhausts
- Ariens Lawn Tractor Fans and Blowers
- Ariens Lawn Tractor Filters
- Ariens Lawn Tractor Fuses
- Ariens Lawn Tractor Grilles and Kickplates
- Ariens Lawn Tractor Hinges
- Ariens Lawn Tractor Hoses and Tubes
- Ariens Lawn Tractor Knobs
- Ariens Lawn Tractor Latches
- Ariens Lawn Tractor Lights and Bulbs
- Ariens Lawn Tractor Pedals
- Ariens Lawn Tractor Pulleys
- Ariens Lawn Tractor Pumps
- Ariens Lawn Tractor Seals and Gaskets
- Ariens Lawn Tractor Seats
- Ariens Lawn Tractor Spindles
- Ariens Lawn Tractor Springs and Shock Absorbers
- Ariens Lawn Tractor Starters
- Ariens Lawn Tractor Switches
- Ariens Lawn Tractor Transmissions and Clutches
- Ariens Lawn Tractor Wheels and Rollers
- Ariens Lawn Tractor Wire Plugs and Connectors