Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Would not fill with water
Ordered most likely part...water inlet valve.
1. Turn off water supply. 2. Remove the metal toe kick plate/insulation at the bottom of the dishwasher. 3. Remove hose to supply valve. 4. Take electrical plug off old valve. 5. Remove float valve because it was mounted it right in the way of the 2 screws on the inlet valve bracket. 6. Remove those 2 screws now you can get to them, and move the inlet valve to one side so you can get to the hose clamp for the rubber hose out of the valve going to the dishwasher. 7, Take the old valve and bracket out, mount new valve on the bracket, crawl back down on the floor, reinstall rubber hose and bracket, and float valve and finally inlet hose. 8. Turn water on. Check hose connections for leaks. Yep, outlet hose didn't clamp enough now, allowing a drip. 9. Repeat the whole process AGAIN. Replace little clamp with a REAL hose clamp, reinstall the thing again. No leak this time. 10. Test run dishwasher thru a cycle. Check again for leaks at hose connections. OK ? Reinstall insulation pieces and toe kick plate.
My wife grabbed the upper rack as she fell backwards across the front of the open dishwasher. It broke her fall - she is fine thank goodness - but the roller slides broke and the rail was destroyed. The dishwasher repair was easy - just had to put new parts in place. The detail parts explosion helps in determining how all physically goes together. Everything works as good as new. I used the pliers to remove one of the old wheel axles that was attached to the basket.
pieces that attach the wheels to the lower rack kept falling off
Ordered the new parts and attached to wheels on lower rack. The old pieces clamped on and the plastic stretched out and would not hold any longer. The 8 new pieces have a slightly different design, were easy to intall and I believe will never loosen up.
This repair was a snap. The parts, though not identical to the original, fit perfectly. I was able to snap both the Rack Slide Cap and the new wheel axle to the existing washer cage and the machine works great now.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Dishes were not drying inside the dishwasher after the dishwasher cycle completed
The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it. The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
