Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The cat brought in a rat which ate holes in the sump inlet.
First, I took off all the pipe clamps and retaining brackets. Then, I pried it out of there. One of the tabs holding one of the other bits to the body got busted, but it didn't matter, as it is held on very well just by the pipe clamp connection. I stuck the new one in and re-attached all the hoses. The GIANT complication was that a new floor had been installed over the old floor, right up against the kick plate- so in order to remove the dishwasher, I had to slice open the counter, as the new floor prevented sliding it out. To prevent the problem recurring, I spray painted over the sump inlet to make it taste worse. This is the downside of a cat door.
Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!
No Plumer could help me. No one heard of a dishwasher check valve. My dishwasher was an ISA. I was lost until i found the relationship to Kitchenaid. Then sears. Vuela! The valve was there, but unavailable. A few more links, and the term "flapper" came up. Well, my dishwasher check valve HAD a flapper inside. Although a plastic pos, i could unscrew the two halves and see the flapper. A little piece of rubber, about 1" in diameter All suppliers gave me but two choices. One large (size given) one smaller. After years of searching, all I needed was a flapper valve. Not the whole check valve. I found it hear for under $10
Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.
I took the front off of the dishwasher door, loosened the screws, unplugged the module and replaced it with the new module. This repair was the easiest repair I've ever completed!
This was very easy. 1) roll out lower rack, 2) rotate lower arm slightly counter-clockwise and lift it out, 3) install new lower arm by dropping into position and rotating clockwise. 4) roll in lower rack, and roll out upper rack, 5) use a nut driver to remove the retaining bolt/screw from the upper arm - it's in the center of the upper arm and you have to work from underside of upper rack, 6) remover upper arm, 7) install new upper arm by holding in position and re-inserting the retaining bolt/screw. 8) Tighten the retaining screw and make sure upper arm freely rotates.
Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order
Removed the dishwasher from the cabinet. Turned it on it's top side. Removed the exit hose from the pump with a nut driver and replaced the flapper. Reconnected the hose to the pump.
This isn't a terribly tricky repair, and the parts are cheap so it's worth a try!
(I had one tricky thing which was the door actuator broke while the door was shut. So I had to get the machine out of it's space without being able to open the front of the machine. I did this by lowering the feet in the front of the machine and then I used a hammer and flat chisel to break the two metal screws I had holding the top of the machine to the top of counter top...a little tricky!)
Remove screws from inside lower panel (where you put soap..the bottom) this will allow you to remove the inside of the door. But be careful as there are still wires attached so be careful to place the inside part without stressing the wires.
I needed to remove the metal harness and to open the black rectangular box that holds the interlock plunger so I could remove the plunger and spring (don't lose..and remember how it goes. take pictures if necessary). Then I was able to remove the broken actuator and see how it all fits together. It rests on top of the latch with notched side facing the inside of the machine. Make sure the notch is centered around where the interlock plunger is located.
Once you have the pieces fit together insert them into the door. Replace the plunger and spring and close the black rectangular box. Then replace the metal harness.
Hold everything in place and put the inside of the door back into position and lock it down with the screws.
You can test the door to make sure it's working but the whole mechanism is less functional when the machine isn't secured into its space. So, if you're mostly sure you've got it right, resecure the machine into its space making sure it's solid and then you should be good.
Like most everyone here I was very happy to accomplish this repair without calling in the repair service!! Awesome.
First of all the part I ordered came a lot sooner than expected. I thought it would take 5 to 10 days. I ordered it on a Tuesday and it was at my door on Thursday. The part was difficult to take off as this was the first time I attempted this. When the new part came, I saw that I went to too much trouble to take the old one off. It was installed in about 40 minutes and we were off and running.
White latch on soap dispenser broken- would not latch
The first posted instruction is dead on (except there are 14 phillips screws (not 10) on inside of door. Also, when reconnecting the 2" quick connect, make sure it is fully inserted - otherwise the numbers on the display panel will not show correctly. Mine didn't the first time, and I had to re-open the door panel and giggle around with the connection to get the numbers to display properly.
Water leak from under dishwasher. Leaky inlet sump
Disconnected the electricity, the drain hose, and the water supply from the dishwasher. Loosened the two screws from the countertop and pulled out the dishwasher. Turned it on to it's side. Saw the damaged inlet sump. Had to remove the Pump connector to get to the inlet sump. Checked it also and discovered that it was starting to develop a small crack from the inside. I decided to replace it as well. The job involves removing the hose clamps and removing the spray mechanizm from the interior of the dishwasher to spin out the inlet sump. Not a difficult job.
I watched the video, read the instructions and went to work. This was the easiest repair I have ever done. I'm 71 and if I can do all 3 spray arms in a total of 15 minutes, anyone can. The hardest part was getting up off the floor when I was finished. The spray arms were all clogged, we have very hard water.