Noisy and Marks Left on Clothes | Spinning Issues | Will not agitate
This part works with the following products:
Washer.
This part works with the following products:
General Electric, Hotpoint.
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Mark B - February 15, 2024
Verified Purchase
Clutch the exact part
It was pretty easy to instal and install a new belt washer works great thanks
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Plastic gear worn and belt stretched from usage
first disconnect the electric power cord. Disconnect the incoming water lines. Tip washer up or better yet flat on the floor where bottom is completely exposed. Remove bolts holding guard over belt and motor. remove bolts [2] holding clutch arm into plastic bearing, remove old belt will slide off pulley, remove bolt holding pulley to shaf
... Read moret, calls for a puller but I applied pulling pressure while working back and froth; no problem but could have been. chance clutch bearing and reverse the process to working order. I would recommend wearing cloth or vinyl gloves once the guards are removed for the pulley and old belt has a lubricant that is somewhat messy but cleans up easy.
washer would make noise when it was spinning and sometime it would not spin out
I contacted parts select and entered washer information and asked them if they thought they would now what the problem was and and they responded with a answer and also a list of two parts that they thought might take care of the problem. I ordered the parts,looked on u tube to see how to change them and replaced both parts .I think the c
... Read morelutch was good but the drive belt was stretched and needed replaced.Know it works great.
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Thomas
September 11, 2021
Washer makes grinding noise when changing into spin mode
For model number GTW680BSJ2WS
Hello Thomas, Thank you for the question. This is normally an indication the Transmission is defective and will need to be replaced. We hope this helps!
Hello Rufus, thank you for contacting us. The most probable culprits of the issue are the bearing retainer platform, part number PS16729511, the clutch, part number PS11729473, and the transmission pulley, part number PS16226205. We hope this sorts out your problem!
My washer makes a little noise but the flor is covered in grease. When I jiggle the pulley the bottom part has movement but I don’t see any play in the shaft that the clutch attaches too. Does the clutch have grease in it? Or is it coming from the bearing
For model number Gtw460asj6ww
Hi Brian, thank you for reaching out. The grease is inside the gearcase transmission, part number PS16729509, and from that part, grease comes out. The noise produced in the washer may be due to the drive belt, part number PS11767488, and the clutch, part number PS11729473. We hope this information is useful!
Washer agitator pulls going clockwise but sometimes slips when going counterclockwise is this the clutch
For model number GTW685BSL0WS
Hi Timothy, thank you for reaching out. Based on the description that you have provided, we would recommend tightening the agitator bolt. If it does not help, you may need to check the agitator base hybrid assembly, part number PS16743416, to fix this issue. We hope this solves your problem!
My washer is not agitating.
It takes in water and spins correctly, however the agitator spins freely in both directions when turned by hand and does not wash the clothes in it.
Please help
For model number GTW335ASN0WW
Hi Randall, thank you for getting in touch. Based on our research, if the agitator is fine, the issue could be with the transmission assembly, part number PS16729509. It drives the agitator and spins the basket in the washer. You may need to replace it to fix the issue. We hope this solves your problem!
