This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your washer may not run because it thinks the door is open, or it will not keep the door locked during the wash cycle. To replace this part, make sure you disconnect power to the appliance and wear work gloves.
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This water inlet valve assembly controls the flow of hot and cold water into your washing machine, ensuring each cycle uses the correct amount of water. If your washer isn’t filling properly, is leaking, or continues to fill even when turned off, the valve may be faulty and require replacement. The part is housed in durable gray plastic a...Read morend does not include a gasket. Installation may require basic tools and should be done with the power and water supply disconnected.
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your washing machine, and if worn out or damaged, must be replaced immediately. If you hear loud or excessive banging noises from your washing mach...Read moreine, this and/or other suspension rods within the washing machine are worn out. This specific suspension rod is the left assembly, so the parts for the other side of your washing machine will also be required when replacing this one, considering they all wear at a relatively similar rate. This suspension rod assembly is sold individually, so it does not come with any other suspension rods.
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and support the drum. The rod is a cylindrical plastic component that connects the drum to the outer frame of the washing machine. The spring is...Read more made of metal and provides tension and elasticity. The assembly is designed to absorb shocks and vibrations while the washer is running to help prevent excessive movement. If the assembly is damaged or out of alignment, the washer will be unstable and noisy. This assembly is designed to fit on the right side of the washer.
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply ...Read moredoes not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitat...Read moreing, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.
This drive belt is an authentic OEM part that is compatible with various models of washing machine. The drive belt is responsible for allowing the drum to rotate smoothly during the wash and spin cycles, as well as driving the pump to drain water from the machine. If the drive belt becomes worn, stretched, or damaged, it can cause issues ...Read moresuch as the drum not spinning or the machine not draining properly. Your washer may also become excessively noisy during use. If the belt is faulty, it will need to be replaced to restore your washer.
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger rotates to move the clothes, lifting them up and then dropping them back down into the water and detergent solution. By agitating the cloth...Read morees, the auger helps to loosen dirt, stains, and debris, to ensure that your clothes receive a thorough and effective cleaning. Signs of a faulty auger include unusual noises like grinding and scraping, incomplete wash cycles, and torn or tangled clothing.
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the perimiter of the lid lock. It features an open slot where the locking mechanism engages. The bezel ensures that the lid lock remains securely in...Read more place and that the locking mechanism functions correctly. If the bezel is damaged or faulty, the lid lock mechanism will be left exposed and vulnerable to damage. You may also notice that the lid lock is loose or unstable, and the door may not lock properly.
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it. If this speed sensor is damaged or bad, it will cause your washer drum to rotate too quickly, slowly, or inconsistently. Replacing this sen...Read moresor will require a screwdriver and some minor disassembly of your washing machine. This sensor is an OEM part and is sold individually, so it does not come with any other parts or accessories.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sheryl - For model number GTW460ASJ5WW
March 5, 2020
Hi! Our GE washing machine started dripping inside the barrel. The next day, the machine turned on by itself and the control panel did not light up/was not lit. So, i've unplugged it and here it sits!
Hi Sheryl,
Thank you for your question. If water is dripping into your washer when it is off, then a component inside the water inlet valve may have failed and it will need to replaced. You will need to test the water inlet valve with a multi-meter. To inspect and test your water inlet valve, disconnect the power source and the water source from your washing machine before beginning. Remove the rear panel of your appliance and locate the water inlet valve. It likely will be located directly behind the hose connections. After removing the valve from the washer, inspect the screens inside the valve for any buildups or debris, removing anything you find. Use caution when doing so as the screens cannot be replaced and if they become damaged you will need to replace the entire valve. You should also inspect the valve for any signs of cracking, wear, or damage. Using a multi-meter on Rx1 mode, place the probes onto the valve’s terminals. The reading you should receive varies from model to model, refer to your owner’s manual for what the reading for a functioning valve should be.
If you receive a reading outside the recommended range, if you receive a reading of infinity, or if your valve is visibly damaged, you will need a replacement water inlet valve. If your washer came on by itself, you should also check the electronic control board for signs of damage, wear or burn marks. If the electronic control board shows any of these signs, it will need to be replaced. We hope this helps. Thank you and have a great day.
My washer makes a loud grinding noise when it rinses and spins and doesn't rinse well. Do you think it is the tub bearing that is rusted? Or what do you think it could be? Thank you for your time!
Hello Christy, Thank you for the question. Normally this is caused by a defective Clutch Assembly. We suggest checking the clutch for wear or damage. We hope this helps!
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Bill - For model number GTW460ASJ5WW
June 19, 2024
Washer fills with water and drains at the same time but continues in the wash cycle.
Hi Bill, thank you for contacting us. Make sure that the house drain pipe is at least 30 inches high. Ensure that the drain hose is not inserted too far into the drain. There must be an air gap around the drain hose. A snug fit can cause a siphoning action. If the house drain is not at least 30 inches high, you may need a drain hose clip, part number PS271098. It attaches onto the drain hose and then onto the back of the washer. This lifts the drain hose up to a proper height to prevent siphoning. We hope this solves your problem!
My washing machine fills with water spins for a little bit but doesn't spin for a full cycle but leaves water on the clothes. The drain hose is clear. What can be causing this?
Hello Steve, thank you for contacting us. According to our research on model number GTW460ASJ5WW, the problem appears to be with the lid switch assembly, part number PS16554755. A faulty switch assembly can generate a false signal of door opening which may stop the washer mid-cycle. If that does not help then the issue is likely to be with the control board, part number PS16743401. This electronic control board manages the washer's functions such as filling, washing, draining, and spinning. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer ran fine but woudl not drain water - low humming noise
62 of 93 peoplefound this instruction helpful.
Mike from NAPLES, FL
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Read less
Was this helpful?
Thank you for voting!
Wife pull up door when it was in lock mode
52 of 96 peoplefound this instruction helpful.
Wiley from Wilson, NC
Really Easy
30 - 60 mins
Screw drivers
Lift up door removed lid lock with screwdriver installed new part
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
My Orders
