This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
Ask our experts a question about this model and we'll get back to you as soon as possible!
18 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rob
January 13, 2020
What is the capacity of my washing machine ?
For model number GTW460ASJ4WW
Hello Rob and thank you for writing.
Your unit has a 4.2 Cu. ft. Capacity. We hope this helps. Please contact us anytime if you require further assistance.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Pamela
September 27, 2023
During the agitation it squeaks loudly but not thru the spinning out.
For model number GTW460ASJ4WW
Hi Pamela, thank you for reaching out. Based on our research, you may need to check the transmission assembly, part number PS16729509, to fix the issue. We hope this sorts out your problem!
My washer does not completely spin the load therefore, leaving clothes full of water. Can you please tell me what parts i would need to correct? It is a Kenmore washer with s/n gg915269g and model number gtw460asj4ww.Thanks!
For model number GTW460ASJ4WW
Hello Tracey, thank you for writing. This is likely due to a faulty Drive Belt, part number PS11767488 for your model washer. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Rose
December 18, 2019
The washer does not fill with enough water. I know its a low water washer that is to save water. But i put a couple of pillows in it and the water didn't even come half way up the pillows. I really hate this washer and i wash i had never bought it. It's not even a year old. Is there anyway i can get it to fill with more water? Thanks
For model number GTW460ASJ4WW
Hello Rose and thanks for writing.
It certainly sounds more like a faulty selector switch ps11759136 and or water inlet valve PS12726769 check for signs of damage and replaces it if needed. We hope this helps. Please contact us anytime.
Hi Brian,
Thank you for your question. To replace the temperature selector, you will need to purchase the selector switch assembly. The part number listed under your model number for the selector switch assembly is PS11759136. We hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Turn off hot and cold water supply valves feeding washer. Disconnect both water hoses from washing machine. Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve. Slightly lift the bottom portion of metal plate and slide to release hooks for
... Read moreeasy removal. Pull back and tilt forward plastic control panel to get it out of your way. Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is. Remove two screws from water inlet valve. (one on each side) Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful. Once you have disconnect the sensor you can remove the water inlet valve. If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve. The new valve DOES NOT come with a replacement O-ring so you will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole. Don't forget to install the O-ring or your washer WILL leak! Put everything back together in reverse order. Check hose connections for leaks. Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.
