Parts That Fix General Electric Washer GTW460ASJ4WW Will not drain
Will not drain is a commonly reported symptom for the GTW460ASJ4WW General Electric Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GTW460ASJ4WW General Electric Washer that will fix Will not drain. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Fixes Symptom 78% of time
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
$
48.21
In Stock
PartSelect Number PS12723115
Manufacturer Part Number WH23X28418
Customer Repair Stories
Would not drain the water from the tub.
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
-
Micheal from South Bend, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
27 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer ran fine but woudl not drain water - low humming noise
Drain all the water out of the tub with a shop vac
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Read less
-
Mike from NAPLES, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
44 of 58 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 14% of time
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your washer may not run because it thinks the door is open, or it will not keep the door locked during the wash cycle. To replace this part, make sure you disconnect power to the appliance and wear work gloves.
$
83.87
In Stock
PartSelect Number PS16554755
Manufacturer Part Number WH08X32697
Customer Repair Stories
The lid switch which signals that the washer door is closed malfunctioned. Even with the lid closed the washer would not spin because the washer was detecting the lid as open because of the faulty switch
The replacement part looked absolutely nothing like the defective part. The old part was easily accessible and was easily unplugged from the wiring harness. I assume when the new part came, I would just plug it into the wiring harness, snap some of the trim pieces in place and be done. 5 minutes. But no. The replacement part was c
... Read more
ompletely different and came with its own wiring harness and length
of wire which had to be installed. The installation of the wiring harness was extremely complicated which involved popping off the control panel of the washer, prying up the top and disconnecting some other pieces to complete the install. There should have been a clear warning on the replacement part, that it was completely different and likely too difficult for a non-professional repair man.
of wire which had to be installed. The installation of the wiring harness was extremely complicated which involved popping off the control panel of the washer, prying up the top and disconnecting some other pieces to complete the install. There should have been a clear warning on the replacement part, that it was completely different and likely too difficult for a non-professional repair man.
Read less
-
Timmothy from EAGLEVILLE, PA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
13 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't fill, wash, spin
Use putty knife to unlock top panel from base. Remove 2 bolts from back of washer holding control section. Don't take completely off. 2 bolts needs to be removed to unsecure top from base. Lastly 2 screws hold lid in place. Remove lid. Slide top panel to left just to access lid lock. Unplug sensor. 1 screw and tabs hold lock in place. Wat
... Read more
ch position coming out so you don't get confused putting new lock in. Squeeze tabs, replace screw. plug in sensor. Reverse procedure to put top section back together.
Read less
-
Susan from OXFORD, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
13 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 3% of time
$
19.86
In Stock
PartSelect Number PS11767488
Manufacturer Part Number WH01X24697
Customer Repair Stories
Noisy operation....belt slipping.
Turned washer on to its side. Removed belt cover, three screws. Removed old belt. Cleaned both pulleys thoroughly, removing all traces of oil. Cleaned grooves thoroughly on motor pulley with small screwdriver. Installed new belt. Replaced cover. Turned washer upright.
-
james from BRONXVILLE, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Won't spin, belt slipping.
Laid washer on the floor to expose the bottom. Cleaned up the residual water that leaked out on to my hardwood floor. Removed the three nuts that hold the belt cover on. Slipped off the two year old stretched, oil soaked serpentine belt. Cleaned the rugged plastic pulleys with alcohol. Put on new belt. Small serpintine pully first, then r
... Read more
otate pulley to install belt to large pulley. Easy fix but doomed to fail again soon. Seals are Junk on the transmission. They leak oil already. Washer is JUNK. Not my first rodeo with GE garbage. It needs a new transmission to truly fix the problem. When it fails again out to the curb it goes. 2 years old, just two in the house so usage was minimal. No more GE appliances for me.
Read less
-
Larry from GROVESPRING, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
13 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 3% of time
$
13.29
On Order
PartSelect Number PS11729471
Manufacturer Part Number WH02X24399
Customer Repair Stories
Washer would not advance to Wash
Lift the cover, undo too screws, Slide out broken part, slide in new part put in the screws and close the lid.A piece of cake.
Thank you for the super fast service on Christmas eve no less!
Thank you for the super fast service on Christmas eve no less!
-
Garry W. from TAMPA, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Don’t do this, but we prop the washer lid open so it doesn’t get musty between use; we put a sock or something in there to prevent the striker fro closing. When a family member hops up on the washer to get to the highest shelf in the laundry closet it snaps! And the. The washer won’t function.
REALLY easy-
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.
-
Heather from CHARLESTON, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 2% of time
$
8.06
On Order
PartSelect Number PS11763265
Manufacturer Part Number WH08X24179