Parts That Fix General Electric Washer GTW460ASJ4WW Will not agitate
Will not agitate is a commonly reported symptom for the GTW460ASJ4WW General Electric Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GTW460ASJ4WW General Electric Washer that will fix Will not agitate. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your washer may not run because it thinks the door is open, or it will not keep the door locked during the wash cycle. To replace this part, make sure you disconnect power to the appliance and wear work gloves.
Customer Repair Stories
The lid switch which signals that the washer door is closed malfunctioned. Even with the lid closed the washer would not spin because the washer was detecting the lid as open because of the faulty switch
of wire which had to be installed. The installation of the wiring harness was extremely complicated which involved popping off the control panel of the washer, prying up the top and disconnecting some other pieces to complete the install. There should have been a clear warning on the replacement part, that it was completely different and likely too difficult for a non-professional repair man.
-
Timmothy from EAGLEVILLE, PA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
Washer wouldn't fill, wash, spin
-
Susan from OXFORD, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Customer Repair Stories
Broken auger; could turn both ways.
-
Cody from BALDWIN CITY, KS
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Agitator broken
Very difficult to remove..Have to apply force and pull.
Theres no bolt inside if the fabric softener part that needed to be adjusted...
-
lisha from PHENIX CITY, AL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
The agitator rotates back and forth to move the clothes inside the tub to clean the load.
Customer Repair Stories
Washer would not advance to Wash
Thank you for the super fast service on Christmas eve no less!
-
Garry W. from TAMPA, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
Don’t do this, but we prop the washer lid open so it doesn’t get musty between use; we put a sock or something in there to prevent the striker fro closing. When a family member hops up on the washer to get to the highest shelf in the laundry closet it snaps! And the. The washer won’t function.
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.
-
Heather from CHARLESTON, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Customer Repair Stories
Noisy operation....belt slipping.
-
james from BRONXVILLE, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Won't spin, belt slipping.
-
Larry from GROVESPRING, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
Customer Repair Stories
Bolt broke in half
-
Rachel from WAXHAW, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set