This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your washer may not run because it thinks the door is open, or it will not keep the door locked during the wash cycle. To replace this part, make sure you disconnect power to the appliance and wear work gloves.
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This water inlet valve assembly controls the flow of hot and cold water into your washing machine, ensuring each cycle uses the correct amount of water. If your washer isn’t filling properly, is leaking, or continues to fill even when turned off, the valve may be faulty and require replacement. The part is housed in durable gray plastic a...Read morend does not include a gasket. Installation may require basic tools and should be done with the power and water supply disconnected.
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your washing machine, and if worn out or damaged, must be replaced immediately. If you hear loud or excessive banging noises from your washing mach...Read moreine, this and/or other suspension rods within the washing machine are worn out. This specific suspension rod is the left assembly, so the parts for the other side of your washing machine will also be required when replacing this one, considering they all wear at a relatively similar rate. This suspension rod assembly is sold individually, so it does not come with any other suspension rods.
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and support the drum. The rod is a cylindrical plastic component that connects the drum to the outer frame of the washing machine. The spring is...Read more made of metal and provides tension and elasticity. The assembly is designed to absorb shocks and vibrations while the washer is running to help prevent excessive movement. If the assembly is damaged or out of alignment, the washer will be unstable and noisy. This assembly is designed to fit on the right side of the washer.
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply ...Read moredoes not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitat...Read moreing, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.
This drive belt is an authentic OEM part that is compatible with various models of washing machine. The drive belt is responsible for allowing the drum to rotate smoothly during the wash and spin cycles, as well as driving the pump to drain water from the machine. If the drive belt becomes worn, stretched, or damaged, it can cause issues ...Read moresuch as the drum not spinning or the machine not draining properly. Your washer may also become excessively noisy during use. If the belt is faulty, it will need to be replaced to restore your washer.
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger rotates to move the clothes, lifting them up and then dropping them back down into the water and detergent solution. By agitating the cloth...Read morees, the auger helps to loosen dirt, stains, and debris, to ensure that your clothes receive a thorough and effective cleaning. Signs of a faulty auger include unusual noises like grinding and scraping, incomplete wash cycles, and torn or tangled clothing.
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the perimiter of the lid lock. It features an open slot where the locking mechanism engages. The bezel ensures that the lid lock remains securely in...Read more place and that the locking mechanism functions correctly. If the bezel is damaged or faulty, the lid lock mechanism will be left exposed and vulnerable to damage. You may also notice that the lid lock is loose or unstable, and the door may not lock properly.
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it. If this speed sensor is damaged or bad, it will cause your washer drum to rotate too quickly, slowly, or inconsistently. Replacing this sen...Read moresor will require a screwdriver and some minor disassembly of your washing machine. This sensor is an OEM part and is sold individually, so it does not come with any other parts or accessories.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tonia - For model number GTW460ASJ6WW
November 30, 2019
Why won't it spin??? why does it always beep when not in use?
Hi Tonia, it may be a faulty door lock. If this part is broken, your washer may not run because it thinks the door is open. Based on the beeping it could also be a faulty control board.Thank you for your question and good luck with your repair!
Fabric softener container does not drain well. Use downy ultra he and usually fill to first line. At least every 5 loads I have to remove and clean container and holes to disperse are all gunked up.
Hello Theresa, Thank you for the question. I suggest checking the water pressure to make sure it is flowing enough to rinse the softener from the cup. Hope this helps!
4 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Robert - For model number GTW460ASJ6WW
March 25, 2022
When in delicate cycle washer bangs
When in normal wash cycle noisy slight grinding
My research says tub bearing...agree?
can't find it on your site
Hi Robert,
Thank you for your question. If your washer shakes and moves, you will need to check the suspension rods, part numbers PS12343380 and PS12343381. If you are hearing a grinding noise when the washer is agitating, then the issue is likely tub bearing. The tub bearing would be part of the gearcase, part number PS12298171. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
My washer will spin, but it won’t agitate. I’ve already put the door switch in and had it spin out but I can’t get it to agitate. Any suggestions?
Hi Butch, thank you for the question. We have concluded that the issue is with the mode shifter, part number PS16554752, which may need to be replaced. The mode shifter is a component that causes the transmission to change between agitation and spinning modes. If the mode shifter is defective, the transmission may be stuck in the spin mode, resulting in the washer not agitating. Before replacing the mode shifter, make sure that the agitator is properly secured and not loose. We hope this helps, good luck with this repair!
Final spin, washer stops, light blinks & washer commences a refill. Control board?
Hello John, Thank you for the question. Depending on what lights are blinking and how many blinks, this could indicate the Control Board is defective. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer ran fine but woudl not drain water - low humming noise
62 of 93 peoplefound this instruction helpful.
Mike from NAPLES, FL
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Read less
Was this helpful?
Thank you for voting!
Wife pull up door when it was in lock mode
52 of 96 peoplefound this instruction helpful.
Wiley from Wilson, NC
Really Easy
30 - 60 mins
Screw drivers
Lift up door removed lid lock with screwdriver installed new part
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
My Orders
