This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
$48.21
In Stock
Order within the next 4 hrs and your part ships today!
Order within the next 4 hrs and your part ships today!
Questions And Answers for GTW335ASN2WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Nelson
December 29, 2023
Machine when finished spinning model keep adding water and not spinning
For model number GTW335ASN2WW
Hi Nelson, thank you for contacting us. Based on our research, the issue is most probably with the water inlet valve, part number PS12726768. You may need to replace it to fix the issue. We hope this solves your problem!
this is the water level knob =needs to be replaced.it is cracked
For model number GTW335ASN2WW
Hello Don, thank you for contacting us. The knob you are looking for is part number PS11726904. If you need help placing an order, customer service is open 7 days a week!
My washer will not fill up on Maximum load. Purchased it October 31,2022. Please help me if I can order a part That would be great. Thank you Arlene
For model number GTW335ASN2WW
Hello Arlene, thank you for your inquiry. Based on our understanding of the issue, we would suggest checking the control board, part number PS16874148, to solve the problem. We hope this helps.
My washer is continuously draining and filling even when the breaker is off. Could this be the water inlet valve?
For model number GTW335ASN2WW
Hi Cynthia, thank you for the question. Yes, the issue could be with the water inlet valve, part number PS12726768. You may need to replace it to fix the issue. We hope that helps!
Hello Larry, thank you for your inquiry. We would recommend resetting the appliance by unplugging it for 1 minute and then plugging back in. If the issue still persists, then you may need to replace the control board, part number PS16874148, to fix the problem. Glad to be of assistance!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
