This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your washer may not run because it thinks the door is open, or it will not keep the door locked during the wash cycle. To replace this part, make sure you disconnect power to the appliance and wear work gloves.
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This water inlet valve assembly controls the flow of hot and cold water into your washing machine, ensuring each cycle uses the correct amount of water. If your washer isn’t filling properly, is leaking, or continues to fill even when turned off, the valve may be faulty and require replacement. The part is housed in durable gray plastic a...Read morend does not include a gasket. Installation may require basic tools and should be done with the power and water supply disconnected.
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your washing machine, and if worn out or damaged, must be replaced immediately. If you hear loud or excessive banging noises from your washing mach...Read moreine, this and/or other suspension rods within the washing machine are worn out. This specific suspension rod is the left assembly, so the parts for the other side of your washing machine will also be required when replacing this one, considering they all wear at a relatively similar rate. This suspension rod assembly is sold individually, so it does not come with any other suspension rods.
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and support the drum. The rod is a cylindrical plastic component that connects the drum to the outer frame of the washing machine. The spring is...Read more made of metal and provides tension and elasticity. The assembly is designed to absorb shocks and vibrations while the washer is running to help prevent excessive movement. If the assembly is damaged or out of alignment, the washer will be unstable and noisy. This assembly is designed to fit on the right side of the washer.
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply ...Read moredoes not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitat...Read moreing, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger rotates to move the clothes, lifting them up and then dropping them back down into the water and detergent solution. By agitating the cloth...Read morees, the auger helps to loosen dirt, stains, and debris, to ensure that your clothes receive a thorough and effective cleaning. Signs of a faulty auger include unusual noises like grinding and scraping, incomplete wash cycles, and torn or tangled clothing.
This drive belt is sourced from the original manufacturer for use in various models of dryers. It is a rubber belt that connects the motor to the transmission of the washer. It enables the drum to spin and agitate during the wash cycle. The belt is prone to wear over time due to the high friction it experiences. The belt may slip, become ...Read morefrayed or lose tension. If the belt is faulty, the drum will have difficulty rotating, you may notice loud banging or squealing sounds, and a burning odor coming from the washer. You can find the belt near bottom of the drum or towards the back.
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the perimiter of the lid lock. It features an open slot where the locking mechanism engages. The bezel ensures that the lid lock remains securely in...Read more place and that the locking mechanism functions correctly. If the bezel is damaged or faulty, the lid lock mechanism will be left exposed and vulnerable to damage. You may also notice that the lid lock is loose or unstable, and the door may not lock properly.
Introducing the GE Spring Clutch, a crucial component for your washer. This intricate item applies steadfast pressure against the shifter hub, dutifully holding it in place for uninterrupted operation. For safe and accurate installation, remember to unplug your washer and wear work gloves to guard your hands. As a member of the renowned G...Read moreE lineage, this spring clutch offers consistent quality and performance. Enhance your washer's functionality today with the GE Spring Clutch.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dale - For model number GTW460ASJ2WW
December 21, 2019
My washer will not drain or spin. It washes fine, but nothing else. I also cannot figure out how to access the interior of the washer
Hello Dale and thanks for writing.
It certainly sounds like a failed drain pump PS12582968 and /or door lock PS12343280 you should check for signs of damage, and replace it if needed. We hope this helps. Please contact us anytime.
For your convenience, we have attached the link to your manual with repair instruction. We hope this helps. Good luck with your repair
https://www.manualslib.com/manual/1054074/Ge-Gtw460asjww.html
My washer will not fill with water to the level set
Hello Jeffery,
Thank you for your question. Our sources suggest replacing the water inlet valve under part PS12726769 for your model to fix the issues. We hope this helps!
I have a drip in washer into tub even when not washing can you tell me what I need.
Hello Blaise, Thank you for the question. This is normally an indication the Water Inlet Valve Assembly is stuck open and leaking water into the Tub. PartSelect Number PS12726769 will need to be replaced. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
My model makes a whining sound from the agitator of when it changes tasks.How is the agitator attached? or could it be the cycle knob rotating?
Hi Lucy,
Thank you for your question. If your agitator is making a whining sound when it agitates, you may have worn motor bearings. To verify if the issue is the motor bearings, remove the belt from the drive pulley and place the washer on the spin cycle. If the noise returns, then you have worn motor bearings and the drive motor will need to be replaced. The part number listed under your model number for the drive motor is PS11763333. If you would like to place an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
My washer will not run the water the first time I turn it on and I have to keep turning it off and on. I had to replace the motherboard like 3 yrs ago. What does this sound like it needs?
Hi Gwendolyn, thank you for reaching out. According to our research, the issue is with the control board, part number PS16743401, or lid lock assembly, part number PS16554755. If these are not causing the issue, then we would recommend checking the water inlet valve assembly, part number PS12726769. you may need to check these parts through the multimeter via a continuity test to fix the issue. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer ran fine but woudl not drain water - low humming noise
62 of 93 peoplefound this instruction helpful.
Mike from NAPLES, FL
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Read less
Was this helpful?
Thank you for voting!
Unit did not go into Spin/Drain cycle.
30 of 33 peoplefound this instruction helpful.
Patrick from GAINES, MI
Very Easy
Less than 15 mins
Nutdriver, Socket set
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
Read less
Was this helpful?
Thank you for voting!
Would not drain the water from the tub.
37 of 58 peoplefound this instruction helpful.
Micheal from South Bend, IN
Very Easy
Less than 15 mins
Socket set
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
My Orders
