This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your washer may not run because it thinks the door is open, or it will not keep the door locked during the wash cycle. To replace this part, make sure you disconnect power to the appliance and wear work gloves.
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your washing machine, and if worn out or damaged, must be replaced immediately. If you hear loud or excessive banging noises from your washing mach...Read moreine, this and/or other suspension rods within the washing machine are worn out. This specific suspension rod is the left assembly, so the parts for the other side of your washing machine will also be required when replacing this one, considering they all wear at a relatively similar rate. This suspension rod assembly is sold individually, so it does not come with any other suspension rods.
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and support the drum. The rod is a cylindrical plastic component that connects the drum to the outer frame of the washing machine. The spring is...Read more made of metal and provides tension and elasticity. The assembly is designed to absorb shocks and vibrations while the washer is running to help prevent excessive movement. If the assembly is damaged or out of alignment, the washer will be unstable and noisy. This assembly is designed to fit on the right side of the washer.
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply ...Read moredoes not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitat...Read moreing, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.
This is an agitator assembly for washing machines. Agitators are used within top load washing machines to move back and forth and effectively wash your clothes. However, if the agitator currently in your washing machine is damaged and/or worn out, it needs to be replaced for your washing machine to operate properly. Replacing this agitato...Read morer assembly will require a wrench, and for you to turn off the power and water supply for your washing machine. This agitator assembly is an OEM part that is sold individually and does not come with any other parts or accessories.
This is a water inlet valve; an electrically controlled solenoid valve that opens and closes when necessary, to control the flow of water into your washing machine during the washing cycle. This part features two different valves, one for cold and one for warm water. If your washer is having difficulty filling up properly or is not fillin...Read moreg up at all, the inlet valves may be bad and not opening to allow water in, meaning the valve needs replacing. Replacing water inlet valves will require some disassembly of your washing machine, so a screwdriver, socket wrench, and other tools will be necessary. This water inlet valve is sold individually, and does not come with any other parts or accessories.
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the perimiter of the lid lock. It features an open slot where the locking mechanism engages. The bezel ensures that the lid lock remains securely in...Read more place and that the locking mechanism functions correctly. If the bezel is damaged or faulty, the lid lock mechanism will be left exposed and vulnerable to damage. You may also notice that the lid lock is loose or unstable, and the door may not lock properly.
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it. If this speed sensor is damaged or bad, it will cause your washer drum to rotate too quickly, slowly, or inconsistently. Replacing this sen...Read moresor will require a screwdriver and some minor disassembly of your washing machine. This sensor is an OEM part and is sold individually, so it does not come with any other parts or accessories.
Introducing the GE Spring Clutch, a crucial component for your washer. This intricate item applies steadfast pressure against the shifter hub, dutifully holding it in place for uninterrupted operation. For safe and accurate installation, remember to unplug your washer and wear work gloves to guard your hands. As a member of the renowned G...Read moreE lineage, this spring clutch offers consistent quality and performance. Enhance your washer's functionality today with the GE Spring Clutch.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian - For model number GTW335ASN0WW
June 24, 2022
Clothes are wetter than normal following spin cycle, sometimes very wet requiring us to "wring" them out before drying. Occurs with even small loads. Water drains out. Spin l.e.d. blinking during spin cycle. Fault code was in for oob, #26 on service bulletin taped to cabinet inside. Agitator spins freely by hand with no bearing noise detected; no bearing noise while machine is running a load either.
Hi Brian,
Thank you for your question. If the clothes are soaked at the end of a wash cycle, the drain hose may not be positioned correctly in the standpipe or it may be clogged or kinked. You should also check the drain pump, the lid switch and the drive belt. We have included a link that you may reference on how to check these parts. If you need to order a part, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
when the the clothes are finished washing there are black particles on the clothes and in the tub. where can the be coming from ? they feel a little waxy
Hello Carol, thank you for reaching out. Based on our understanding, these black particles are of detergent. We would recommend checking the water inlet valve assembly, part number PS12726768, to fix the issue. If the hot water is not coming properly, then detergent will not dissolve and make marks on the clothes. We hope this helps!
Washer barrel spins out and continually bangs against side of machine
Strapping holding barrel evenly appears to not keep barrel balanced
Hello Brenda, thank you for reaching out. We believe one or more of the suspension rods might be broken. The suspension rods help to dampen the movement of the washer tub. You need to replace your left suspension rod and spring assembly, part number PS12343381, and the right suspension rod and spring assembly, part number PS12343380. We hope this helps.
Hello, my machine is shaking and violently hitting the sides of the machine, I have already replaced the suspension rods and it seemed like it worked alittle better but a couple weeks later its back to doing its thing again. Is it the tub that needs to be replaced or something underneath it?
Hello Zack, thank you for reaching out. Based on our understanding of the issue, we would suggest replacing the gearcase, part number PS16729509, to solve the problem. We hope that helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer ran fine but woudl not drain water - low humming noise
62 of 93 peoplefound this instruction helpful.
Mike from NAPLES, FL
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Read less
Was this helpful?
Thank you for voting!
Unit did not go into Spin/Drain cycle.
30 of 33 peoplefound this instruction helpful.
Patrick from GAINES, MI
Very Easy
Less than 15 mins
Nutdriver, Socket set
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
Read less
Was this helpful?
Thank you for voting!
Would not drain the water from the tub.
37 of 58 peoplefound this instruction helpful.
Micheal from South Bend, IN
Very Easy
Less than 15 mins
Socket set
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
My Orders
