Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
lower rack took one min. take out old slide in new
upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off. total time for this part 15 min.
Note: This procedure assumes replacement of both eyelet cables. It is recommended that both eyelet cables be replaced at the same time.
1. Using a Philips' head screwdriver, remove the four screws holding the lower front panel (below dishwasher door). 2. Remove the faulty eyelet cable(s) hooked into the springs at one end and the door hinges at the other. 3. Take the new eyelet cables and hook them onto the door hinge on either side. Ensure a secure fit. 4. Guide the eyelet cable around the spinwheel on one side and insert the hooks of the springs into the eyelets. 5. Pull on the springs and insert their hooks into the eyelets of the other cable, ensuring a secure fit. 6. Test the door by opening and closing it a few times to ensure the spring has tension. 7. Replace the lower front panel cover removed in step 1 with its screws.
Dishwasher leaks from bottom of door......when operated.
Removed 7 screws holding "inner door" in place ( note: 2 bottom screws are different than the rest...keep separate).....remove rinse aid plug....press "tabs" inward to release rinse aid container. ( in this instance....the gasket had failed...which was "part" of the reason dishwasher was leaking during operation)
install new rinse aid container ...making sure that "trip arm" is positioned correctly........and press into place. ( Tabs should expand when container is properly positioned...creating a tight seal).....reuse old rinse aid filler plug.
Replace "inner door" cover....tighten screws.....
remove faulty tub corner baffles....place new ones in corresponding positions ( the baffles form a suction .....to stay in place....no adhesive needed)
Close door and operate as usual........no more leaks!
This is a super easy "no brainer"...that would have cost about half the price of a new dish washer ...had I hired a "professional" to do the repairs!!!!
Opened package from Parts Select. Removed Silverware basket from package. Opened Dishwasher. Inserted Silverware Basket in rack. Closed Dishwasher. Discarded shipping package. Told wife I fixed Dishwasher. Sat down & had a beer.
Motor was getting noisier every time we used the dishwasher. We knew it was just a matter of time before it totally quit.
The most difficult part was removing the dishwasher from below the counter. Once that was complete, I simply turned the washer onto it's front surface to access the pump easier. Simply disconnected the electrical connectors, loosened the three hose clamps holding the hoses to the pump. Lastly removed a stiff arm bracket holding the pump. Reversed the order to install the new one using a longer bracket provided with the new unit. Hooked up the electrical connections last and slid the washer back in place. The washer runs like new now and is not making noise. The replacement part was a perfect match.
front twoo rack rollers broken ,bottom rack roller broken
for the top rollers you must remove thethe end cap. this was easy ,i placed a block of wood on the outside .placed the punch on the inside where the channel is pushed in to hold cap on. smacked it till it was pushed out far enough to remove end cap. new rollers simply snap on. very easy,
Top of the water spray "tower" was broken off by opening lower dish drawer and not checking to see if tower was in the down position.
Apply large vice like pliers at base of the lower spray arm and not applying too much pressure to plier as this is an all plastic part and slowly turn counter-clockwise until entire spray arm is loose enough to lift out and install the new part in the reverse order.
water coming our of dishwasher from upper part of spray arm water supply hose, hole in upper part of hose due to corosion
unscrewed 2 screws found on upper part of dishwasher that connected hose to spray arm found inside of dishwasher to remove hose. gently squeezed rubber gasket to work it into the hole found at the top center of the dishwasher, made sure rubber disc shaped gasket was seated properly into spray arm, screw spray arm back into place. The job was much easier than I thought It took about 20 minutes it saved me from buying a new dishwasher, the delivery of the hose was faster than the speed of light it took about i business day, I order the hose on saturday it arrived tuesday evening. Thanks for your excellent service
Removed 4 screws in washer then removed cover. Then piston and nut assembly which just needs turned loose.Pull out and then,put new one back in,tighten up, put cover back on put 4 screws back in. Then unhooked water line, power cord, drain hose. Pull washer out and drained water out of system with drain hose. put a towel down to catch excess water. Loosen nut at end of drain hose with a pliers, remove flapper put new one back in tighten drain hose . Put washer back in hook water, power and drain hose. Run thourgh cycle and it should work much better.
took dishwasher out- put on table to work on-removed wire brace- disconected drain outlet- disconnected top drive seal- removed wire clip connector- removed motor unit---------------- installed new motor/drain unit--used new longer wire brac used adapter to connect electical leads- tightened clamps and bingo it worked and didnt' leak. good job on the supplying of all the necessary adapers.
First I removed the dishwasher from underneath the countertop and laid it on its back. I used a nut driver to remove the pump support wire and the two clamps holding the rubber connectors to the pump. It helped to hook the pump support wire in a hole in the left side of the frame and reconnect it to the pump to hold it up out of the way. I was able to remove the rubber connector by hand and unscrew it. To install the new rubber connector tightly, I slipped a piece of 2" PVC pipe (outside diameter is 2-3/8") inside the connector and tightened the clamp around the connector and PVC pipe. This allowed me to use the pipe to tighten the rubber connector. I reassembled the dishwasher pump and connections and put the dishwasher back into service
Went to www.PartSelect.com. Part was easy to locate online with GE model number and illustraion online. They shipped the parts in two days and I put the new parts on by hand. Saved a $135 service call from GE. One part came in broken from the factory. Upon calling customer servce, PartSelect sent out a replacement part the next day - no problem. Great service, would be happy to use again - Thank you!