Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Set aside time (6-8 hours), not rocket science, but long
Clear a work space, set up bins for parts, there are a lot of them, so upon removal, put all parts in same place (motor bolts in same box as motor, etc), use a digital camera to capture where everything goes. Remove back, remove front lower access panel. Remove all plumbing from tug. Remove belt and large pulley from back (tap gently with mallet around perimeter to remove). Unhook motor wire connector, cut the zip tie. Remove the motor (4 bolts). Separate the front seal, remove the shock absorbers (use a deep socket to push in plastic tabs). Now the fun part, carefully tilt the washer back to the floor (2 people, it is heavy), while supporting the tub, to keep it from over swaying (I cut a 2x4 to size, put it between the tub and the lips of the side walls to keep it in place). You should now be able to remove the springs (leverage them out with old screw driver), clear all parts from the tub. You can then lift the washer housing from the tub vertically. You should then be able to access the tub clearly. Remove the counter weights, set aside carefully, they are fragile. Remove the bolts holding the tub together. Tap out the tub. Reverse the process to put back together. Careful not to over tighten the bolts on counter weights or motor.
Dryer would not start. When turning on, I could hear faint humming, but the motor would not start.
1) Unplug the unit. 2) Remove all screws from top of the unit except for the one in the center front that does not go through the outer casing. 3) Find the Thermal Limiter which is on the back wall near the top on the left side when looking from the front. 4) Disconnect the two wires 5) Remove the two screws that mount the limiter to the back wall. 6) Use an ohmeter to test if a current flows through the unit. If no current flows through (an open switch), then the unit will need to be replaced. 7) Clean any lint that you can at this point. 8) Use two screws to mount new Thermal Limiter 9) Reconnect the two wires to the Limiter. 10) Attach the top of the dryer case.
Unplugged the dryer from electrical socket. Vacuumed lint from dryer and exit hose. Removed top from dryer. Used pliers to remove the 2 wires from the thermal limiter. Used screwdriver to remove 2 screws that held the limiter in place. Installed the new limiter, connected the 2 wires, plugged in the dryer's electrical connection, turned on dryer, and resumed my "washday chores".
I unplugged the washer. Then I unscrewed the two screws on the back, top edge of the washer. and lifted the top off. Next I unscrewed the door lock/switch assembly, reached down in the machine from the top and pulled the switch out. As I unplugged each one of the three plugs from the bad part, I plugged them into the corresponding connections of the good part. Then I screwed the switch back into place, replaced the top of the washer and screwed it back on. I set the washer spin and cheered madly when it went into spin mode. The hardest part was actually turning the screws because I'm a small woman and my hand strength is not what it used to be. But really there was nothing difficult about this repair.
This unit is a stackable washer&dryer,so first pull unit away from wall atleast 4 foot. Unplug power cord,then take10 dagree front panel off then the control panel off and unplug the 5 connetors if your unit has that many,then lay panel asside. Take dryer door off,makes it easier when putting it all back together. Now take front panel off and the dryer lent tube,now just take the 3 center phillips head screws out and slide drum out. Pull upward on what they call the shaft which held drum on. Now these are the parts you should order. Belt,grounding ball clip,grounding ball,drum support bearing,bearing bracket,and most important part is the shaft. The shaft is ur insurance for the whole job. Use a good grease like white lithium grease and coat the shaft end and the drum support bearing. The grease will cut down on friction for a while,and re assemble the way you took apart. Reminder grounding ball goes behind drum support bearing not in front. Good luck and please vaccum.
drum vane had a hole in it replaced it using phillips screwdriver removed one screw ,pulled drum vane towards the door then pulled up replaced it reversing the procedure. It actually seemed to fix my leak during spin cycle
Washing machine wouldn't drain or spin. It would run through its cycle, but only agitate.
Use a cup to take the water out of the washer. Get at least three large towels -- you're going to have to sop up the water when you disconnect the hoses.
Take the bottom panel off (2 Phillips head screws). Drain pump is on the right side.
Remove the two screws holding the pump to the metal bottom plate. Use a small socket wrench and/or a screwdriver. I had to use a screwdriver on the right screw and a socket wrench on the left screw! Place as many towels in the cavity as you can to catch the water that's going to come out when you detach the hoses.
There is an inlet hose and an outlet hose, attached with bright green clamps. Remove those with pliers. Clean up the water that drains out. The hose in the back (inlet) has a "coin catcher" area. Clean this out.
Attach the hoses to the new pump. Screw it down. Replace the bottom panel.
First: Remove front and top cover Second: remove electrical cover assbly Third: motor belt removed Fourth: drum assbly and bearing shaft and bracket bearing replaced Now I need urgently (already ordered) the thermostat and glide drum
The hardest part was figuring out how to get the lid off. You simply remove two screws from the back of the lid and jerk and slide the lid towards the back of the machine. Take out the screws that hold the front panel on, tilt the front out and access the lock/switch assembly and replace.
Removed (1) philips screw in toward back of vane (closest to rear of drum), pulled the vane forward to remove it, slid the new one in place, replaced the screw, and was done in less than two minutes. Piece of cake.
After reading about similar problems people have had with this make of dryer, I focused attention on the thermal limiter. I determined that it was the culprit by "jumping" it with a 6" piece of wire. Then I simply went on the site, ordered the part. It arrived a few days later and I pulled out the old one, screwed in the new one, and the dryer is good as new.
Using a cordless drill and driver bit I removed the back cover, bottom front cover and top. I then removed the rubber bellowed hose connecting the soap dispenser to the rubber boot in front. This one was tricky to reinstall because the fastener for the hose is twisted steel wire that needs to be undone when reinstalling. It slid off easily enough but would not slide back on easily. There is a second small bellowed hose that connects the dispenser to the outer drum casing. This needs to be removed as well. It comes off easily and went back on easily. I used a one sided razor to cut the glue dots connecting the front boot to the washer door frame. After that I removed the belt from the motor and drum pulley by hand and then removed the motor mounting bolts using a ratchet and socket. This went smoothly. I now propped up the drum using 4x4 cutoff blocks to take the weight off the springs and shocks. I then removed to the lower upper plastic pins that hold the shock onto the plastic spin drum casing. I used a wooded block and a hammer to tap the pins out. Be sure to push in the lock on the tapered end of pin shaft. The second pin was a little more difficult to remove and required quite a bit of tapping to push it all the way through. I tried adjusting the weight on the shocks several times to make it easier to come out. The pin was slightly damaged by the time I got it out from hitting it. It went back in OK so I don't think the damage will cause any problems. Next I got someone to help lift the drum to release the weight on the springs and removed then from the top end. You need to remove the spring clamps that hold the spring down at the top end. I used a wrench to remove the bolt that holds the pullet on the drum shaft. The pulley was easy to pry off shaft by placing two flat screw drivers between the shaft and the bearing casing and twisting the screw drivers. Once the pulley was removed I turned the spin drum casing upside down and supported the outer casing with two stacks of 4x4 cutoff blocks. This would allow the stainless steel drum to be supported above the floor and drop freely as the shaft worked it way out of the bearing casing. Getting the drum shaft out of the outer housing bearing was the most difficult part of this whole process. The shaft was rusty and therefore did not easily slide through the two bearing casings. Before hitting the drum shaft to remove it from the bearing casing I put the washer and bolt back on the shaft to protect the shaft from hammer/mallet damage. I tried a mallet but it only moved the shaft part way and then it wouldn't slide further. I then used a 1/2" steel pipe cutoff as a punch seated around the pulley bolt to alloy me to use a hammer to beat the shaft out of the bearing casing. It required a tremendous amount of force to move the shaft. Once the shaft was removed from the old drum casing I spent some time cleaning the back of the stainless steel drum including using emery cloth to remove the rust from the shaft and polish it the best I could. Be sure not to damage the brass bushing that the rubber bearing seal rides on to prevent water leakage. Once the drum and shaft were cleaned up the reassembly process when smoothly I simply reassembled the washer in the reverse order or the disassembly. The shaft went into the new bearings snugly which I was pleased to see since the snug fit meant that the water would be sealed in and the drum would spin true. The hardest part was reattaching the large bellowed hose onto the soap dispenser because it require undoing the twisted steel wire clamp and getting it back together in a very tight space. I use a combination of a flat screw driving and a needle nose pliers to wrestle it back together. The finished job resulted in a very quiet smoothly operating washer which we expect will give us another 5 years of service.
Water wouldn't drain from washing machine and clicking sound when trying to run
Used a shop vac to suck all the water through the drain hose. Removed the bottom front panel held by two screws on bottom and two plastic pins at the top. Removed electric connector on front of pump. Removed two screws holding pump down. Used pliers to move spring clips back so hoses could be removed. Put hoses on new pump and squeezed clamps with pliers to pull them back over the hose connection. The connection on the left was a little bit of a pain due to space limitations. Screwed the new pump down and reconnected the electric plug. Put the bottom cover back on and screwed it into place.