Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bake element cracked on its own
Flipped the breaker. Removed shelf, Find the right size nut socket, unscrew the two screws, pull the element out a little bit, disconnect the wires (on pretty tight), pull out element, clean out any mess in the oven, compare element with new one to make sure its the same size and such, connect wires to new element, replace screws, flip breaker back, turn on for a few minutes to make sure it works. Piece of cake.
Oven took 30 minutes to get to 380 degrees-no hotter
First I searched this site and read about the repairs - which made me feel like my husband could do it with ease. Then he removed two screws inside the oven, removed the broken element (didn't know it was broken til removed) and replaced the new one - just like that! The real key was being able to read how it was for other people who had already done it. That's the only reason I'm submitting my storey. Thanks
Watched a repairman do it the last time for $200.00. This time I unplugged the stove, unscrewed four screw nuts holding the upper rear cover, unplugged old wires, reconnected new ones, fed them thru to the front, attached them to the new block, screwed the block into place, replaced back cover, stuck the element into place, made my little brother plug it back in and turn it on first. It worked. Cost me $20.00 to do what the repairman did the last time. I also replaced the reflector pans. No-brainer.
I turned off the power to the oven at the breaker. Then I removed the two screws from the old element, pulled the old element out about 3 inches and disconnected the wires from the element and installed the new one.
Removed 2 screws that hold element and pulled old element out about 2 inches to disconnect the wires from the old element. Connected the new element and remounted to rear oven wall. Very simple and saved a visit from the appliance repairman.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires the repeated the process to complete the installation. Relly easy.
TURNED OFF CIRCUIT BREAKER. Removed nut, washer and screw, pulled out electric burner about three inches, disconnected electric terminals and removed damaged element. Inserted new element into oven, connected electric terminals, pushed electric prongs back in, screwed element to back wall of oven....DONE Easy as 123
unplugged unit pulled it away from wall took off the backplates traced wire to plug replaced with part ordered very smooth operation. the most impressive thing to me was i ordered part on computer and it was at my door in 30 hours awesome.
Before removing screws, I reached in and felt for where the upper end of the spring attached to the hinge. There are three holes in the end of the hinge arm, so I wanted to be sure of which hole to use. (The holes are very close together, so if the spring falls out before you determine which hole it was in, it probably won't matter so long as you are sure to use the same hole on both new hinges.) I then removed three Phillips screws per hinge. Once the hinge was loose, I could wiggle it around and release enough of the spring tension to slip the top end of the spring out of the hole on the hinge arm. Then I pulled out the old hinge and inserted the new one and replaced the three screws. Without the tension, the lower end of the spring fell out of the little hole in the oven bottom where it normally attaches. Our gas oven has a broiler rather than a storage drawer, so it was a little difficult to get the lower tip of the spring back into that hole. It actually ended up being easier to get the lower tip of the spring back into that hole first, before trying to reattach it to the hinge arm. Once I got the lower end into that hole, I pulled up on the spring and maintained upward pressure on the spring while I fiddled around to get the upper end into the hinge arm hole. Took about 20 minutes, door works perfectly now. Lots of sharp edges inside the oven, so had to be careful.
Turn circuit breaker off.Raise up cook top and remove 6 screws that hold catch pan in place.move 3 screws that hold switch cover panel [2 sections]in place. Pull off knob for bad switch and remove 2 screws.Pull off each of the 5 wire terminal clips by removing one at a time and replacing that one on the new switch control to assure correct placement.Reinstall switch cover panel and catch pan.