Crosley Washer Springs and Shock Absorbers
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Crosley Washer Springs and Shock Absorbers
Your Price
$81.29
In Stock
Crosley Washer Suspension
PartSelect Number PS12347546
Manufacturer Part Number W11130362
This suspension rod kit is a genuine OEM replacement kit that is compatible with various models of washing machine. The kit is responsible for supporting the inner tub of the washing machine and absorbing any excessive vibrations and movement caused during the washing and spinning cycles. This helps to protect the tub and interior of the washer from damage. If the suspension rods in your washer are faulty, you will likely notice loud banging, knocking, or scraping sounds as the tub makes contact with the washer cabinet. Each kit includes four suspension rods and springs as well as the suspension ball cups. It is advised you replace all suspension rods at the same time, as they tend to wear at similar rates.
Fixes these symptoms
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
Jesusa from JEFFERSON CTY, MO
Washer wobble during spin cycle.
Watched a video to get a general idea. Moved washer to garage. Raised lid, supported with s-hook and light chain. Front springs were easy, except no hole for the rod to hang in so used chain and small screwdriver through mounting hole. Back springs were not as easy. Finally removed the back panel to get to the rods. Bingo, much easier and only took 5 min to remove the back panel. reassemble and she works like a charm. Suggest to find a video reflecting your particular brand and model as all are similar but uniquely different. Easy project though.
Read more...
Your Price
$9.95
In Stock
Crosley Washer Suspension Spring
First I disconnected the washer from the water and power supply, then I laid it on its back.
The tub rested on the back of the washer, making two of the three suspension springs relax, and they were pretty easy to pull out with pliers. After the first two were out, I had to support the tub with a couple 2x4s to relax the third suspension spring.
Installation was the reverse of removal - install the lower suspension spring, remove the 2x4s, then install the two other suspension springs.
The tub balancing spring was easy to replace, and probably wasn't the cause of the problem.
With $25 in parts and about 15 minutes, my washer spins much more quietly. Read more...
PartSelect Number PS11743345
Manufacturer Part Number WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could cause the load to be off-balance which can lead to excessive shaking, moving, noise, and leaks. For this repair, you will need a 1/4 nut driver, a putty knife, a flat blade screwdriver, and a pair of needle-nose pliers. Disconnect the power supply, fill hoses, and drain hose to give you safe and easy access (have a container nearby for water left in drain hose). This item is sold individually, which is important as you may need to repair multiple springs in your appliance, which carries three suspension springs. As an inexpensive part, we recommend purchasing several at a time, as they can be very useful to have on-hand.
Fixes these symptoms
- Leaking
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
Brian from Seattle, WA
Washer tub slammed into washer body during spin cycle
If you load a washing machine unevenly, it will spin out of balance. But our washer seemed to make noise during the spin cycle regardless of how the load was distributed. I suspected that the suspension or balancing springs were getting tired, and ordered a replacement set.First I disconnected the washer from the water and power supply, then I laid it on its back.
The tub rested on the back of the washer, making two of the three suspension springs relax, and they were pretty easy to pull out with pliers. After the first two were out, I had to support the tub with a couple 2x4s to relax the third suspension spring.
Installation was the reverse of removal - install the lower suspension spring, remove the 2x4s, then install the two other suspension springs.
The tub balancing spring was easy to replace, and probably wasn't the cause of the problem.
With $25 in parts and about 15 minutes, my washer spins much more quietly. Read more...
Your Price
$57.37
In Stock
Crosley Washer Washing Machine Suspension Rod Kit
PartSelect Number PS11703290
Manufacturer Part Number W10780048
This suspension rod kit is a genuine OEM kit specially designed for washing machines. Each kit includes a set of 4 rods, 4 suspension balls and 4 bushings. The suspension rods are responsible for supporting the washer tub and allowing it to move freely during the wash and spin cycles while minimizing vibrations and noise. The suspension rods, balls and bushings may fail over time due to cracks, breaks, or excessive wear. If the suspension rod kit is faulty, you will likely notice excessive vibration or shaking during the spin cycle, loud banging noises, or the washer not balancing properly.
Fixes these symptoms
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
Terry from Homosassa, FL
Crosley Washer Suspension Rod Kit
PartSelect Number PS11703288
Manufacturer Part Number W10780045
Fixes these symptoms
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
Harold from MELROSE, FL
Shaking violently during spin cycle
Replaced the 4 suspension rods/springs. Only disconnect and replace one at a time. The tub will fall out if you disconnect and replace more than one rod/spring at a time.
Read more...
Your Price
$6.95
In Stock
Crosley Washer Tub Spring
PartSelect Number PS11751118
Manufacturer Part Number WPW10250667
This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front of the front-load washer so the washer tub sits straight and even during the spin cycle. You may need to replace the spring if tub is sitting tilted forward. A broken spring will result in the tub being off-balance during the spin cycle which can cause further damage to washer parts. It is recommended to check all suspension springs as they often wear at the same rate. Tools needed for repair are a Phillips screw driver, flat blade screw driver, and a pair of pliers.
Fixes these symptoms
- Leaking
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
RICHARD from PHILA, PA
Replace Water Pump Coupling
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump.
Read more...
Your Price
$46.95
In Stock
Crosley Washer Shock Absorber Kit
PartSelect Number PS3508101
Manufacturer Part Number 5304485917
This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.
Fixes these symptoms
- Leaking
- Noisy
- Shaking and Moving
- See more...
Installation Instructions
Douglas from Medical Lake, WA
Both vibration shock absorbers broken
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.
Read more...
Your Price
$9.95
In Stock
Crosley Washer Spring
PartSelect Number PS3497596
Manufacturer Part Number W10400895
Tub centering spring
Fixes these symptoms
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
Timothy from E PALESTINE, OH
WASHER ON SPIN CYCLE WOULD SHAKE, MAKE NOISE AND WALK ACROSS FLOOR
FOLLOWED VIDEO INSTRUCTIONS, UNPLUGGED AND REMOVED WATER LINES AND DRAIN, REMOVED HARNESS COVER PLATE. MOUNT SCREWS AND TOP, UNHOOKED SUSPENSION RODS(FOUND THEY HAD LEFT OUT TOP SPRINGS FROM TUB TO SUSPENSION RODS WHEN MANUFACTURED) PUT TOP BACK ON WITH ONE SCREW, PUT ON SIDE, REMOVED AND REPLACED SUSPENSION RODS, HOOKED THEM TO SIDE CABINET, SAT UNIT BACK UP, INSTALLED NEW PLASTIC CUPS AND TOP SPRINGS(HAVE TO ORDER SEPERATE) INSTALLED RODS IN LOCKING CAPS, PUT TOP BACK ON, PUT HARNESS COVER PLATE AND MOUNTING SCREWS IN, HOOKED UP TO WATER, AND DRAIN, LEVELED UNIT, PLUGGED IN AND WASHED CLOTHES, NO PROBLEMS, WORKS GREAT.
Read more...
Crosley Washer Suspension
PartSelect Number PS12347544
Manufacturer Part Number W11130359
This is a suspension rod kit for washing machines. Suspension rods are what make up most of the suspension within your washer and are used to ensure the inner drum does not shake or bang excessively against the washer cabinet. Suspension rods can wear down over time and will eventually no longer work as well as they used to, so if any of the suspension rods in your washing machine are worn out or broken, they will need to be replaced. This suspension rod kit comes with all four approximately 27-inch-long suspension rods you would need, as well as the securing accessory parts. Replacing these suspension rods will require some disassembly of your washing machine, so a screwdriver, wrench, and flat tool with likely be necessary. This suspension rod kit is an OEM part.
Fixes these symptoms
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
Gregory from Seminole, FL
Out of balance code , shaking during spin cycle
Removed three screws on back to open top panel, used small vice grip to pull on suspension rod to unhook and remove from the drum. Remove and replaced one at a time so the rods keep drum suspended and prevent from dropping in the cabinet . Reinstalled top panel and done .Very easy completed in about 20 minutes.
Read more...
Your Price
$13.95
In Stock
Crosley Washer Tub Wear Pads (3 Pack)
PartSelect Number PS334620
Manufacturer Part Number 285744
This package of pads contains three tub wear pads.
Fixes these symptoms
- Shaking and Moving
- See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.
Read more...
Your Price
$9.95
In Stock
Crosley Washer Leveling Spring
PartSelect Number PS394983
Manufacturer Part Number 8316845
This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.
Fixes these symptoms
- Leaking
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
john from middle river, MD
Machine rocking about like crazy on spin
Took some online research to figure out how to get the cabinet off. Once inside I fitted the wear pads which were a breeze to remove using a knife blade to pry them up and removing them using the screwdriver. The springs were replaced one by one using strong fingers. The machine went through the spin cycle without any rocking or self-destruct noises.
Read more...
Related Crosley Washer Parts
- All Crosley Washer parts
- Crosley Washer Agitators
- Crosley Washer Bearings
- Crosley Washer Belts
- Crosley Washer Brackets and Flanges
- Crosley Washer Caps and Lids
- Crosley Washer Circuit Boards and Touch Pads
- Crosley Washer Dispensers
- Crosley Washer Doors
- Crosley Washer Drums and Tubs
- Crosley Washer Hardware
- Crosley Washer Hinges
- Crosley Washer Hoses and Tubes
- Crosley Washer Knobs
- Crosley Washer Latches
- Crosley Washer Legs and Feet
- Crosley Washer Motors
- Crosley Washer Panels
- Crosley Washer Pulleys
- Crosley Washer Pumps
- Crosley Washer Seals and Gaskets
- Crosley Washer Switches
- Crosley Washer Transmissions and Clutches
- Crosley Washer Valves
- Crosley Washer Wire Plugs and Connectors