Crosley Washer Motors
Popular Crosley Washer Motors
Your Price
$27.84
In Stock
Crosley Washer Direct Drive Motor Coupling
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
PartSelect Number PS1485646
Manufacturer Part Number 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Fixes these symptoms
- Burning smell
- Leaking
- Noisy
- See more...
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
Your Price
$141.82
In Stock
Crosley Washer Motor with Pulley
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble. Read more...
PartSelect Number PS11738839
Manufacturer Part Number WP21001950
This motor is a 2 speed, 1/2 HP, 120V, 60Hz.
Fixes these symptoms
- Burning smell
- Will not agitate
- Will not drain
- See more...
Installation Instructions
Michael from Warminster, PA
The belt and pulley on the drive motor broke
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble. Read more...
Your Price
$188.98
In Stock
Crosley Washer 2-Speed Drive Motor - 60Hz 120V
PartSelect Number PS11743427
Manufacturer Part Number WP661600
This is a 2-speed drive motor for your washing machine. The motor rotates the spin basket when the washing machine is in spin or tumbling mode. You will likely need to replace the motor if you are experiencing burning smells or your washer will not start. The tools you will need to make this repair include a number two Phillips screwdriver, a flat-blade screwdriver, and a 5/16 nut driver.
Fixes these symptoms
- Burning smell
- Will not agitate
- Will not drain
- See more...
Installation Instructions
Lowell from Dover, DE
Washer had water leak in lower front and would not drain.
Laid the washer on its back and found leak in water pump. Found out it was caused by vibration from motor with bad bearing. Removed pump and motor which were held on by clips. Both were removed and replaced without removing cabinet from machine.
Read more...
Crosley Washer Drive Motor
PartSelect Number PS11770267
Manufacturer Part Number W11026785
The drive motor spins the spin basket and drives the agitator or spin basket in the agitation or tumbling mode.
Your Price
$294.96
In Stock
Crosley Washer Drive Motor
PartSelect Number PS2373340
Manufacturer Part Number 137043000
This motor is used on front load washers.
Crosley Washer MOTOR Assembly - 1/3 HP
PartSelect Number PS11726282
Manufacturer Part Number W10832724
Crosley Washer Drive Motor with Pulley
PartSelect Number PS815482
Manufacturer Part Number 134156400
This motor has 3/4 hp and 1 speed.
Related Crosley Washer Parts
- All Crosley Washer parts
- Crosley Washer Agitators
- Crosley Washer Bearings
- Crosley Washer Belts
- Crosley Washer Brackets and Flanges
- Crosley Washer Caps and Lids
- Crosley Washer Circuit Boards and Touch Pads
- Crosley Washer Dispensers
- Crosley Washer Doors
- Crosley Washer Drums and Tubs
- Crosley Washer Hardware
- Crosley Washer Hinges
- Crosley Washer Hoses and Tubes
- Crosley Washer Knobs
- Crosley Washer Latches
- Crosley Washer Legs and Feet
- Crosley Washer Panels
- Crosley Washer Pulleys
- Crosley Washer Pumps
- Crosley Washer Seals and Gaskets
- Crosley Washer Springs and Shock Absorbers
- Crosley Washer Switches
- Crosley Washer Transmissions and Clutches
- Crosley Washer Valves
- Crosley Washer Wire Plugs and Connectors