My Orders
Crosley Washer Pumps
GET YOUR OFFICIAL Crosley PARTS TO ENSURE VICTORY
Popular Crosley Washer Pumps
This drain pump for your washer is designed to remove the dirty water during and after the washing cycle. If your washer has water left in it after its washing cycle is over, or if your washer is experiencing leaks around the drain pump, the pump may be damaged or bad and in need of replacement. Ensure you remove and test your drain pump with a multimeter before replacing it. Replacing this pump will require some disassembly of your washer. This pump is sold individually, and does not come with any wire harness or other accessories.
This drain pump for your washer is designed to remove the dirty water during and after the washing cycle. If your washer has water left in it after its washing cycle is over, or if your washer is experiencing leaks around the drain pump, the pump may be damaged or bad and in need of replacement. Ensure you remove and test your drain pump with a multimeter before replacing it. Replacing this pump will require some disassembly of your washer. This pump is sold individually, and does not come with any wire harness or other accessories.
Installation Instructions
JASON from HILLIARD, FL
Drain pump was cracked
Turned washer on its side. Pulled the bottom plate off. Then unplugged the electrical lines. Then unbolted the drain pump and bolted the new drain pump in. Then reversed the process.
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is supposed to drain the water from the washer; if the water isn’t draining or if there is a leak, you may have a problem with your pump. You must replace this part if there is a blockage or clog. Although the symptoms may point to a malfunctioning drain pump, there could actually be a problem with one of the connecting hoses. This pump connected directly to the motor, and comes in white plastic. This replacement part features 1 direct drive water pump with 2 ports for water to pass through: a large one and a smaller one.
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is supposed to drain the water from the washer; if the water isn’t draining or if there is a leak, you may have a problem with your pump. You must replace this part if there is a blockage or clog. Although the symptoms may point to a malfunctioning drain pump, there could actually be a problem with one of the connecting hoses. This pump connected directly to the motor, and comes in white plastic. This replacement part features 1 direct drive water pump with 2 ports for water to pass through: a large one and a smaller one.
Installation Instructions
RICHARD from PHILA, PA
Replace Water Pump Coupling
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump.
This drain pump is specially designed to fit in top load washing machines. It is responsible for removing water from the washer tub during the drain cycle and directing it to the household plumbing system through the drain hose. If you notice longer draining times, grinding or rattling sounds, or standing water in the tub at the end of a cycle, the drain pump is likely faulty. This may be due to several reasons such as normal aging, wiring problems or physical damage. It is also common for the drain pump to become clogged with small items such as coins or buttons.
This drain pump is specially designed to fit in top load washing machines. It is responsible for removing water from the washer tub during the drain cycle and directing it to the household plumbing system through the drain hose. If you notice longer draining times, grinding or rattling sounds, or standing water in the tub at the end of a cycle, the drain pump is likely faulty. This may be due to several reasons such as normal aging, wiring problems or physical damage. It is also common for the drain pump to become clogged with small items such as coins or buttons.
Installation Instructions
Hoa from Greer, SC
No drain
Take the old one out and put a new one in
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
Installation Instructions
kenneth from willard, OH
would't spin all water out or rinse out clothes
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and
... Read more
fix problem washes like new spins and drains all water from tub.
Read less
If your washer isn’t draining properly or making strange noises, this drain pump could be the fix. It’s the part that helps push water out of the tub during the cycle, keeping everything running smoothly. Made to fit select top-load models from Whirlpool and other brands, it’s a reliable replacement if your machine is leaking or not spinning out water. Just make sure it matches your model before ordering, and unplug your washer before installing.
If your washer isn’t draining properly or making strange noises, this drain pump could be the fix. It’s the part that helps push water out of the tub during the cycle, keeping everything running smoothly. Made to fit select top-load models from Whirlpool and other brands, it’s a reliable replacement if your machine is leaking or not spinning out water. Just make sure it matches your model before ordering, and unplug your washer before installing.
Installation Instructions
REED from BUCHANAN, NY
Wouldn’t drain pump made loud noise
Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This genuine OEM drain pump is designed for washing machines. It is responsible for removing the wastewater from the machine during the drain cycle. The drain pump works by creating suction to draw water out of the tub and push it out through the drain hose. Signs of a faulty drain pump include the washer failing to drain water properly, leaving clothes wet at the end of the cycle, or loud, unusual noises during the drain cycle, such as grinding or humming sounds. Additionally, if the drain pump is visibly damaged, or leaking, then it likely needs to be replaced. You can find the drain pump located at the bottom of the washing machine.
This genuine OEM drain pump is designed for washing machines. It is responsible for removing the wastewater from the machine during the drain cycle. The drain pump works by creating suction to draw water out of the tub and push it out through the drain hose. Signs of a faulty drain pump include the washer failing to drain water properly, leaving clothes wet at the end of the cycle, or loud, unusual noises during the drain cycle, such as grinding or humming sounds. Additionally, if the drain pump is visibly damaged, or leaking, then it likely needs to be replaced. You can find the drain pump located at the bottom of the washing machine.
Installation Instructions
Kris from W MANSFIELD, OH
Washer would not drain
Im a 58 year old single woman. Swap out of pump motor was so easy. Took less than 15 min. Ordered the part on Tuesday it came the next day. I installed it and did 4 loads of laundry.
Great company.
Great company.
This washer drain pump assembly is designed to efficiently remove water from front-loading washing machines during the drain cycle. It plays a critical role in maintaining proper water flow and cycle completion by actively pumping water out of the drum. Compatible with a wide range of models across multiple brands, including Frigidaire, Electrolux, Kelvinator, White Westinghouse, Kenmore, and Tappan, this component ensures reliable performance and long-term durability. Replacing a faulty pump can resolve issues such as standing water, incomplete cycles, or drainage failure. Installation may require basic tools and should be performed with the appliance disconnected from power and water sources.
This washer drain pump assembly is designed to efficiently remove water from front-loading washing machines during the drain cycle. It plays a critical role in maintaining proper water flow and cycle completion by actively pumping water out of the drum. Compatible with a wide range of models across multiple brands, including Frigidaire, Electrolux, Kelvinator, White Westinghouse, Kenmore, and Tappan, this component ensures reliable performance and long-term durability. Replacing a faulty pump can resolve issues such as standing water, incomplete cycles, or drainage failure. Installation may require basic tools and should be performed with the appliance disconnected from power and water sources.
Installation Instructions
Charles from Raleigh, NC
drain pump motor had seized as result of foreign objects
After turning off water, disconnecting power, and sucking water out of the tub and drain hose with a shop vac, I removed the front kick panel (took out two sheet metal screws). Then I removed two mounting screws from the pump assembly, and disconnected two hose clamps (inlet and outlet hoses) with a pair of pliers. Very simple, very easy
... Read more
. The pain in the fanny came when I tried to reattach the hoses. The hose clamps apparently require either a special tool or a technique I'm not familiar with. I finally tossed them and purchased two standard screw and band hose clamps which made the final connections a breeze. The surprise came when I found that the motor had seized because of a pair of tweezers that had somehow worked into the motor impeller. Free of tweezers and coins, the new motor works great! To quote another one of your contributors: wife happy!
Read less
This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is activated after the spin speed has been maintained for a specific period of time and is driven by the same drive belt that also runs the transmission pulley. If your washer is not draining properly the pump could be clogged by a small object or could be broken and in need of replacing. Tools you will need for this repair include a 5/16 nut driver, a putty knife, a 3/8 socket with a ratchet, and a pair of slip joint pliers.
This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is activated after the spin speed has been maintained for a specific period of time and is driven by the same drive belt that also runs the transmission pulley. If your washer is not draining properly the pump could be clogged by a small object or could be broken and in need of replacing. Tools you will need for this repair include a 5/16 nut driver, a putty knife, a 3/8 socket with a ratchet, and a pair of slip joint pliers.
Installation Instructions
David from Boca Raton, FL
washing machine was making alot of noise
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and shakes during operation, you may need to replace the drain pump. This is a redesigned part. The pump now mounts on to the base of the washer. This product is made of white plastic and has a metal center. Before you can replace the drain pump, you will have to disengage the drive belt under the machine. To reach the drain pump you will need to remove the access panel on the backside of the washing machine.
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and shakes during operation, you may need to replace the drain pump. This is a redesigned part. The pump now mounts on to the base of the washer. This product is made of white plastic and has a metal center. Before you can replace the drain pump, you will have to disengage the drive belt under the machine. To reach the drain pump you will need to remove the access panel on the backside of the washing machine.
Installation Instructions
Ranse from Layton, UT
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A
... Read more
small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.
Read less