EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

Crosley Washer Hinges

Popular Crosley Washer Hinges

This is a door hinge, which allows for your washer door to properly shut during the washing cycle, and open after it is finished. If your door hinge is bent or broken and not allowing the door to shut properly, this hinge needs to be replaced immediately. Replacing this hinge will require a screwdriver to remove and install. This door hinge is an OEM part made of durable metal, and does not come with any other parts, like the necessary securing screws or install bracket.
This is a door hinge, which allows for your washer door to properly shut during the washing cycle, and open after it is finished. If your door hinge is bent or broken and not allowing the door to shut properly, this hinge needs to be replaced immediately. Replacing this hinge will require a screwdriver to remove and install. This door hinge is an OEM part made of durable metal, and does not come with any other parts, like the necessary securing screws or install bracket.
What this part fixes:
  • Door Sags
  • Door won’t close
  • Lid or door won’t close
Installation Instructions
Sandy from MILWAUKIE, OR
One of the hinges broke, making the door sag
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with all the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hinge. This lid hinge is an inch and a half long, all white in color, and it is made entirely of plastic. To complete this repair, you will need a Phillips screwdriver and a putty knife to remove the top of the washer, in order to access the screws that hold the lid hinge in place. Be sure to disconnect the power to the washing machine before beginning this repair.
The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hinge. This lid hinge is an inch and a half long, all white in color, and it is made entirely of plastic. To complete this repair, you will need a Phillips screwdriver and a putty knife to remove the top of the washer, in order to access the screws that hold the lid hinge in place. Be sure to disconnect the power to the washing machine before beginning this repair.
What this part fixes:
  • Lid or door won’t close
  • Will Not Start
Installation Instructions
Allen from North Little Rock, AR
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plastic. This lid hinge pin is just over an inch long, is sold individually, and does not include the mounting screw (consider ordering mounting screw if it rusted or stripped). It is recommended to check the opposite lid hinge pin before ordering because hinges may wear at the same rate. Be sure to not tighten the mounting screw to pin too tightly to avoid breaking the new part.
This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plastic. This lid hinge pin is just over an inch long, is sold individually, and does not include the mounting screw (consider ordering mounting screw if it rusted or stripped). It is recommended to check the opposite lid hinge pin before ordering because hinges may wear at the same rate. Be sure to not tighten the mounting screw to pin too tightly to avoid breaking the new part.
What this part fixes:
  • Lid or door won’t close
  • Will Not Start
Installation Instructions
Allen from North Little Rock, AR
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
Installation Instructions
Nicola from Centreville, MD
Washer would not run, lid switch broken
Repair was easy. Removed two side panels on the control plate. Removed two phillips screws that hold the control panel to the body of the washer. Disconnected the electic connection to the wires leading to the lid switch. Three sided of the lower cover lift over and removed from the washer frame. Access to the lid switch and wire retainers was easy. Removed two screws holding the remaining parts of the switch and replaced with new. Re-routed the wires through the retainers. Set the sides back on making sure the set all the way back in the frame and fit properly into the plastic strips on the back of the washer. Reconnected wires, screws and end caps.
$9.62
In Stock
This is the bearing for the lid hinge. Sold individually.
This is the bearing for the lid hinge. Sold individually.
What this part fixes:
  • Lid or door won’t close
Installation Instructions
Enrique from Miami Shores, FL
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Original Equipment Manufacturer

MAKE THIS REPAIR A GUARANTEED WIN

OVER 2 MILLION PARTS TO ENSURE VICTORY

This is a replacement lid hinge for your washer. It is approximately 2.5 inches in length and 1.5 inches in width. The lid hinge is what the lid for your washer pivots on. If the lid hinge is damaged, the washer lid may not open or close properly. The lid hinge is screwed into the washer lid. You will need a Phillips-head screwdriver to detach it. There will be a lid hinge on either side of the lid, so be sure to determine if you need to replace both hinges, or only one.
This is a replacement lid hinge for your washer. It is approximately 2.5 inches in length and 1.5 inches in width. The lid hinge is what the lid for your washer pivots on. If the lid hinge is damaged, the washer lid may not open or close properly. The lid hinge is screwed into the washer lid. You will need a Phillips-head screwdriver to detach it. There will be a lid hinge on either side of the lid, so be sure to determine if you need to replace both hinges, or only one.
What this part fixes:
  • Lid or door won’t close
Installation Instructions
Benjamin from LAKE ODESSA, MI
The lid on our washer would not close fully or stay up when opened.
I removed the two hinges in the lid by unscrewing them from the lid and sliding them out from the underside of the lid. I also needed to replace the hinge assembly in the washer body on the left side. I unscrewed the three screws in the back of the controls module and lifted the cover off. I unscrewed the furthest forward and left screw that went down to the hinge assembly. I then removed the trim ring around the bleach pour spout and unclipped the bleach hopper from the lid. Next I unlatched the lid assembly with a metal putty knife. Once inside I moved the bleach hopper out of the way and gained access to the left side hinge assembly. I removed the other screw holding the hinge in place and changed out the hinge assembly. I then worked backwards putting screws and pieces back in place. Finally, I installed new door hinge pins in the left and right sides to reattach the lid.
$54.24
In Stock
Installation Instructions
Joseph from Warwick, RI
Door hinge worn.
Very easy.I used a screw driver to remove and install the new hinges. Three screws on each hinge. Door closes like new again.
$58.55
On Order
What this part fixes:
  • Lid or door won’t close
$9.62
On Order
Sold individually.
Sold individually.
Installation Instructions
Ellen from NYACK, NY
machine wouldn't turn on when lid closed
replaced missing screw and pad and now machine works perfectly
$20.37
In Stock
Right Side - This lid hinge is for washers. Lid hinge connects the lid to the top panel and allows the lid to pivot open and closed. Wear work gloves to protect your hands when installing this part.
Right Side - This lid hinge is for washers. Lid hinge connects the lid to the top panel and allows the lid to pivot open and closed. Wear work gloves to protect your hands when installing this part.