Crosley Washer Seals and Gaskets

Crosley Appliance Parts

Popular Crosley Washer Seals and Gaskets

Your Price
$212.72
  In Stock
Crosley Washer Front Load Bellow
★★★★★
★★★★★
23 Reviews
PartSelect Number PS12074757
Manufacturer Part Number W11106747
Fixes these symptoms
Your Price
$5.76
  In Stock
Crosley Washer Centerpost Gasket
★★★★★
★★★★★
6 Reviews
PartSelect Number PS11723081
Manufacturer Part Number W10814296
This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, and made of plastic material. To perform this repair, you will need to disconnect the power, drain hose, and the inlet hose. You will need to remove the entire outside cabinet to have access to the tub assembly. The tub will need to be removed entirely. This is a genuine part that is sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...
Your Price
$7.69
  In Stock
Crosley Washer
★★★★★
★★★★★
1 Review
PartSelect Number PS11742027
Manufacturer Part Number WP3949550
This part goes on the agitator retaining bolt.
Fixes these symptoms
Installation Instructions
Patrick from Marysville, WA
The upper agitator arm would not rotate
It was extremely easy. I removed the plastic cap under the softener dispenser, removed the nut and washer that holds the upper agitator in place and then replaced the parts that came in the kit. The most important note for those who may be doing this job is that the o-ring for the cap under the softener dispenser, the seal washer for the bolt and the thrust spacer under the upper agitator all came with the kit. I did not realize that and ordered them all seperately. Read more...
Your Price
$11.10
  In Stock
Crosley Washer Seal, Inner Cap
★★★★★
★★★★★
11 Reviews
PartSelect Number PS11748108
Manufacturer Part Number WPW10072840
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inches in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Leaking
  • Spins slowly
  • See more...
Installation Instructions
Lennis from Jacksonville, NC
Would not agita.
It was a blessing that I ordered the kit, because I thought it only needed the rubber seal and the four dogs. But because the seal and dogs cost less than the shipping I decided to order the kit and its good I did because the nochage on the basket sleeve was broke off. The blessing is that the sleeve was in the kit, sp it took 5 sec to slip it on along with the rest of the kit, and after about 15 min my wife was back to work. Thanks for saving me time and money without this web site I would have bought another brand new washer, thanks. Lennis from NC. Read more...
Your Price
$11.10
  In Stock
Crosley Washer Transmission Stem Seal
PartSelect Number PS11746747
Manufacturer Part Number WP8577376
Sold individually.
Fixes these symptoms
Installation Instructions
Bob from East Palestine, OH
The motor turned with loud noise ,but nothing else worked
I used "Emley's Cheap and Easy Repair" book to remove,install and reassemble the machine.
A lot of time was used to clean the filthy tub and basket.
While replacing the broken motor coupling I decided to replace some of the seals.
PartSelect got the ordered parts to me in a couple of days.
I wouldn't hesitate to do the job again.
Read more...
Your Price
$11.14
  In Stock
Crosley Washer Spin Pinion Seal
PartSelect Number PS11741857
Manufacturer Part Number WP356427
This seal is for the top of basket drive tube shaft.
Fixes these symptoms
Installation Instructions
Bob from East Palestine, OH
The motor turned with loud noise ,but nothing else worked
I used "Emley's Cheap and Easy Repair" book to remove,install and reassemble the machine.
A lot of time was used to clean the filthy tub and basket.
While replacing the broken motor coupling I decided to replace some of the seals.
PartSelect got the ordered parts to me in a couple of days.
I wouldn't hesitate to do the job again.
Read more...
Your Price
$285.08
  In Stock
Crosley Washer Bellow Kit
★★★★★
★★★★★
4 Reviews
PartSelect Number PS1148773
Manufacturer Part Number 134515300
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle. NOTE: This part has been redesigned by the manufacturer and is interchangeable with the old design.
Fixes these symptoms
Installation Instructions
Peggy from New Castle, PA
Old Bellow Ripped
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse. Read more...
Your Price
$8.00
  In Stock
Crosley Washer SEAL-SHAFT
★★★★★
★★★★★
1 Review
PartSelect Number PS11746864
Manufacturer Part Number WP91939
This OEM upper transmission shaft seal, also known as the oil seal, is found in your washers and dryers. It acts as a barrier to prevent water from leaking into the transmission assembly. It measures 1/2 inch in height with a 1-inch diameter, and is located at the top of the transmission shaft where it enters the tub. Signs of a broken seal include water stains, dampness, or pooling of water beneath the appliance. If left unreplaced, it can result in water damage to internal components, along with the potential for corrosion, mold growth, and unpleasant odors. To remove the shaft seal, consult your user guide for specific instructions. Start by shutting off the power and water supply. Remove the water hoses and drain hose, being cautious of any water that may leak out. You will need tools like a putty knife, screwdriver, nut driver, pliers, spanner, plastic mallet, and a socket set. Open the lid and proceed to remove the agitator assembly, detach the control panel, and disconnect any necessary wiring harnesses. Remove the cabinet and water break. Continue disassembling the inner tub until you can lift it out of the appliance and tilt it onto its back, propping it up with a block. This will allow access to the transmission assembly from beneath the appliance. Remove the mounting fasteners on the pump to reach the motor assembly. Once the motor assembly is out, further disassemble it to access the basket drive. The seal can be removed from the top of the shaft of the drive tube, below the thrust ring. When purchasing parts for your appliance repair, it is important to remember that your appliance uses various seals and gaskets. It is important to ensure that you purchase the correct part when making repairs.
Fixes these symptoms
Installation Instructions
Al from OCEAN, NJ
drive shaft leaking
Washer was leaking -- in part from hoses that had loosened over time due to unbalanced loads and age, and partly from a worn pump -- and not agitating/spinning properly. Fixed hoses, replaced pump and clutch. Unfortunately, when I pulled apart direct drive to replace clutch, the drive shaft started leaking because old seals worn and compromised on disassembly. Have to give credit where due -- YouTube invaluable here -- pulled and disassembled drive shaft, removed old seals, replaced and reassembled. Time consuming, but if you keep track of where things go, not too bad. 3 things I wish I knew in advance: (1) for an old washer you definitely need a spanner nut wrench (like 15-25 bucks online) to remove the spanner nut so you can pull the basket and get to the seals -- no wrench/pliers/vise substitute will do the trick; (2) the shaft seals have metal washers inside the rubber/plastic -- when you're removing the old seals, you might need to chisel (hammer and small flat head screwdriver) the old seals out instead of just pulling out the corroded rubber which will leave the old metal behind; (3) if your time is valuable, try to diagnose all the likely sources of your problem and buy the parts to repair at once rather than doing piecemeal like me. Took me 2 weeks and two complete tear downs to finish a repair that should have taken me an afternoon. I love my local Appliance Parts guy -- he's knowledgeable and usu. has what I need or can get it fast and I like supporting local brick and mortar -- but if time is important to you, taking advantage of online companies that allow you to return what you don't use may save you time. Read more...
Your Price
$53.67
  In Stock
Crosley Washer SEAL-TUB
★★★★★
★★★★★
5 Reviews
PartSelect Number PS3407958
Manufacturer Part Number W10324647
Fixes these symptoms
Your Price
$74.78
  In Stock
Crosley Washer Tub Seal Assembly
★★★★★
★★★★★
5 Reviews
PartSelect Number PS459481
Manufacturer Part Number 5303279394
If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make sure water does not lead from between the outer tub and the spin basket from around your basket drive shaft within your washer. To replace your old part with this one you will need a flathead screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16 socket, spanner wrench, and a hammer.
Fixes these symptoms
Installation Instructions
Rick from Walkerton, IN
The primary problem was that the tub seal assembly was leaking.
1. I began by removing the two screws that hold the front panel in place. I then lifted the top free of the front panel and tilted it back to get it out of the way.

2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.

3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.

4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.

5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.

6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.

The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy.
Read more...

Related Crosley Washer Parts