Crosley Washer Switches

Videos!

Your Price

$120.36

Front Load Washer Door Lock and Switch Assembly

★★★★★

29 Reviews

PartSelect Number PS12364048

Manufacturer Part Number 131763256

This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the door does not open or lock. Your washer will not start if the door does not lock. This part is also known as a washing machine door lock assembly. As per the manufacturer, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.

Fixes these symptoms

Leaking
Lid or door won’t close
Spins slowly
See more...

Installation Instructions

DOUG from KING FERRY, NY

Door on washer wouldn't lock or start

1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. Read more...

Videos!

Your Price

$45.97

Washer Lid Switch

★★★★★

76 Reviews

PartSelect Number PS11745957

Manufacturer Part Number WP8318084

This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is having trouble starting, is not agitating, spinning, or is not draining properly, this could be because the lid switch has broken. You will need a 5/16-inch nut driver for this repair. The package will contain one lid switch. You will need to access the back of the washer, and remove the two Phillips screws that hold the top back panel in place. Slide the panel forward to release. Use your nut driver to loosen the screw that holds the ground wire in place. Lift the lid of the washer to release the old lid switch.

Fixes these symptoms

Burning smell
Will not agitate
Will not drain
See more...

Installation Instructions

Clint from Kansas City, KS

Washer wouldn't run

I removed the two screws on the back of the control panel. The control panel then flips back. The switch is on the left side. To remove the switch, I first detached the wire to the control panel and unscrewed the grounding wire. The new switch drops right in. I had a little trouble getting it in until I realized the washer lid had to be open. A little awkward but once it's in you can shut the lid and then I reattached the wire from the control panel and screwed in the grounding wire. Pretty easy. $20 for the part (with shipping) and 15 minutes. Way cheaper than a repairman. Read more...

Videos!

Your Price

$52.86

Lid Switch

★★★★★

83 Reviews

PartSelect Number PS11722098

Manufacturer Part Number 3949247V

This switch (Lid Switch Assembly With Leads, Washer Lid Switch, Lid Switch Assembly, Washer Lid Switch) tells the washing machine that the lid is closed, which allows the wash cycle to begin. The lid switch mounts to the underside of the cabinet top panel. The plastic on the actuator can become brittle with age and break when the lid is closed roughly. It can also break from the movement of an unbalanced load causing parts of the washer to strike it. This part must be replaced if it is broken and no longer being activated by closing the lid (indicated by the washer not agitating properly, or the machine not detecting the lid is closed). This switch is black plastic with wire leads. It is sold individually.

Fixes these symptoms

Lid or door won’t close
Not draining
Touchpad does not respond
See more...

Installation Instructions

Travis from Pearland, TX

Washer stopped mid cycle

1. Unplug washer.
2. Remove screws at control panel end caps.
3. Flip control panel back to expose wiring.
4. Detach lid switch wiring harness from control panel.
5. Use screwdriver to pry the 2 brass clips holding the back panel of the washer to the front and sides piece.
6. Tilt the front/sides piece over to expose lid switch.
7. Use nutdriver to detach ground wire.
8. Use screwdriver to remove 2 screws holding lid switch in place.
9. Install new lid switch. Make sure wiring harness piece is facing the right direction.
10. Put washer back together in same order it was disassembled. Make sure front/sides piece connects to the clips at the bottom. Read more...

Your Price

$55.53

Water Level Switch

★★★★★

2 Reviews

PartSelect Number PS11754877

Manufacturer Part Number WPW10448876

This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside the switch. More water that enters the tub, more pressure is applied against the switch.

Fixes these symptoms

Will not drain
Will Not Start
See more...

Installation Instructions

George from ORO VALLEY, AZ

Door locked because of faulty water level switch

First some background. The door locked up the first time when appliance was less than one year old. The "Maytag Repairman" finally succeeded in getting the door open after propping up the front of the machine and fumbling around underneath for a period of time and then assured me the problem was solved. The problem recurred less than a year later, and I called another repairman who seemed to have an easier time of it, and charged $293.42 to replace the water level switch. About six months later the same problem recurred and I took the cover off the top of the machine and found there a booklet "For Service Technician's Use Only". VERY HELPFUL. Told how extremely easy it was to unlock door - took about five seconds. Replacing the switch itself involved pulling one tubing off and disconnecting one elec connection from old switch and replacing on new switch. Total cost $50 plus a few dollars for shipping. Read more...

Videos!

Your Price

$29.94

Door Switch Kit

★★★★★

19 Reviews

PartSelect Number PS1964648

Manufacturer Part Number W10169313

This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble, replacing the door switch can solve this appliance problem. The tools needed for replacement are a screw driver and wire strippers. Make sure to attach the two wires to the right two poles of the new switch, to do this you can check the resistance of the switch. Unplug the dryer before installing this part, also refer to the diagram provided by the manufacturer.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Don from Jacksonville, FL

Switch sticking in on position

FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two screws, one on the left side, and one on the right, remove these screws, and pull slightly down on panel to remove. Behind this panel find two screws holding the door panel, one on the left, and one on the right, remove the left, and support the door panel while removing the right side. Gently pull the bottom of door panel outward, and the clips on top of door panel will unhinge from top, carefully rotate left side of door panel to floor, and note the wire connections on switch, and orientation of switch, then unplug wires, and move door panel to a comfortable working positon. Door must be open to remove switch, then depress the two plastic retaining keepers on each side of switch, and push switch through toward door. Replace with new switch, reconnect the wires, and reassymble in reverse order. Remember, door assymbly must be inserted in dryer top at an angle, and then bottom rotated downward, and bottom panel nylon guildes inserted into door panel bottom. Read more...

Your Price

$125.84

Water Level Pressure Switch

★★★★★

6 Reviews

PartSelect Number PS3408149

Manufacturer Part Number W10339251

This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside the switch. More water that enters the tub, more pressure is applied against the switch.

Installation Instructions

Chris from LIBERTY TWP, OH

Washer was not filling with water to proper level (was filling some, not enough)

Ordered part PS3408149 from partselect.com. Lifted Washer control panel with putty knife. Removed hinges (regular screwdriver, used as a crowbar rather than screwdriver) holding control panel to washer body. Moved washer body panel out of the way, and reviewed level sensor/level selector switch. Take handle off front of selector switch. Twist selector switch off from inside (90 degree turn till square inset lines up withsquare hole, then it will come out). Insert new selector switch. Remove old tubing. Fish new tubing through where old tubing was. Cut off extra tubing, then push tubing onto selector switch and tub basin (where old tubing was). Put washer back together. Done. Worked perfectly. Read more...

Videos!

Your Price

$80.20

Water Level Switch

★★★★★

7 Reviews

PartSelect Number PS3408155

Manufacturer Part Number W10339326

This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside the switch. More water that enters the tub, more pressure is applied against the switch.

Installation Instructions

Steve K. H. Chun from Redwood City, CA

Water in washer would continue to fill and overflow

Read on Internet to diagnose and get at part.
Luckly they sent new fill hose along with level control switch
as that was problem. Visually there was no
kink or blockage. Upon removing hose, I discovered
a slit on hose which did not allow pressure
to actuate diaphram. I installed new switch
and never thought to return as savings instead
of calling repairman was a no brainer !!!
Word of caution " never force"when removing or
installing a part. It should be easy Steve, Ca. Read more...

Your Price

$77.33

Water Level Switch

★★★★★

3 Reviews

PartSelect Number PS3408118

Manufacturer Part Number W10337780

This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside the switch. More water that enters the tub, more pressure is applied against the switch.

Installation Instructions

Jonathan from Hayden, ID

Tank was overfilling, lots of water on the floor, not good.

Disassembled the control panel and replaced the water level sensor, but not the hose - bad idea. It was probably just the hose. The thing tested fine for 3 fillings. I told my friend to watch it closely for the first couple of loads, because I thought the level was not consistent? - but she didn't. More water on the floor. Replaced the hose and it's working fine. Thank you. Read more...