Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Augur blade broken
Ice maker assembly removed from refrigerator and disassembled. Note nylon nut holding the Augur in place is removed clockwise. As you take the assembly apart, note each piece for reassembly.
I downloaded a schematic of the ice dispensing unit. The whole unit pulls out and there are a couple of screws that remove plastic covers. The "trick" was to get the two plastic tabs pushed in and lift the auger unit out of the tray - a two person job! We used knife blades (it was the thinist and strongest tool around) to push the tabs in and pry the auger assembly out. I think we did a great job NOT breaking the plastic pieces! As careful as I was, I definately needed the schematic to put the ice crushing blades and spacers back together. All of this could be avoided if they used a metal auger instead of plastic!
Watched video, however could not get outer casing off. Under the panel are three small holes, pushed up with an Allen key, used a small screwdriver to wedge out, came out easily, followed instructions from video on removing and replacing solenoid
Fresh food section lights were all out, but the bulbs tested good elsewhere.
I popped the switch out using the blade of a small screwdriver and noticed that it connected with two wires via a slide on connector for each one. I noted the info on the old switch to identify which wire went to which terminal. I held each wire with a pair of pliers while I pulled the wire connector off the terminal on the old switch. I connected the two wires to the correct terminals on the new swith, and popped the switch back into the door frame. Easy, easy, easy and saved the $40 service call + parts cost!
Ice buildup. The Ice Machine was frosting over. Ice (due to frosting) would block the drop chute.
Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.
Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.
plastic broke off the original auger of the ice maker
The ice maker has plastic parts in the front that snap together. Getting those parts apart and back together was the most difficult part of the process. The auger was easily replaced.
It was more involved than I thought. I didn't have the proper tool for removing the snap washers but a screw driver and pliers did the trick with no damage. I think this is the first time I repaired something right the first time.
The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!
First, I removed the top drawer blocking the area where I needed to put the glass panel cover. Then, I removed the drawer along with the glass panel holder to which I needed to install the glass. I installed the glass to the panel holder without difficulties (although the glass cover was expensive :() and reinstall the drawers back to their proper place. This repair was actually a no-brainer.
i removed srews from area until i could access the fan unit and removed it. wires were not identical so i had to splice some together, most likely could not have been avoided. the exploded parts diagram helped me to be sure that i would have all replacement parts on hand so i wouldn't have to wait for something i had forgotten.
I followed the directions provided by Robert of Florida. My contribution is, be aware that the plastic nut on the auger shaft turns to the right to loosen.
I received part. I then used a hair dryer to smooth out kinks. Took about 15 minutes. Pulled off old gasket and replaced with new one. Used hands only.
Groove for retainer clip on auger nut was broken out.
After removing three screws on the ice bucket, it basicly came apart by itself. I needed to use pliers to remove the old nut because it had over tightened itself onto the shaft. Be careful here - it is a left hand nut - not a normal right hand nut! Reassembly was a snap putting the parts back together in reverse order. Unit has been working great since the repair.
I followed the isntructions of another fellow who had repaired his ice maker, but made the mistake of taking the ice crushers apart before noting where the fixed blades were to be reassembled. Since there was not a schematic with the part I had to go on line to your site and enlarge and use the one there, while accurate, was very hard to read and when I finished, I think it is in the wrong place as I'm not able to get the fineness of crushed ice I had before the repair, but absent a very legible schematic I'm not going to try to fix it further. The auger works, gives us ice cubes and half crushed cubes. Another tip for future repairers is to to wait for the ice container to warm up or use a hair drier on the part where the tabs need to be depressed to slip off the blade housing. When cold it's extremely brittle, but since I had to leave the job for later at one point and left in on my work bench I found it much more pliable and easy to assemble. All in all, I'm OK with the part and the result, but wish I could have gotten the fixed blade back into the right spot.