Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer over flows and floods floor
1. Noticed there was and obstruction in the air line that feeds the water level pressure switch. Cleaned out the air line but still had intermittent problem with flooding. 2. Evaluated the fill solenoid valve with meter and was functioning properly 2. Evaluated pressure level switch with meter and noticed that the switch was not changing state as it should when the water level is increasing. Replaced the level pressure switch, but still had problem. 4. Noticed the air line was damaged and had a hole that prevented pressure from building up. Replaced the air line and all is good!
Repaired Agitator - required to pull from the bottom pulling on one side a little more then the other. Once you got loose it comes right off. Under neith there is a bolt that holds on agitator coupler. remove the bolt with wrench or socket wrench and then the agaitator coupler. Replace with new agitator coupler ,make sure grooves are aligned when putting on the rotor. Tap the top of the agitator coupler lightly until it is completely seated. Put the bolt on with wrench or socket wrench. Put the agitator back on over the agitator coupler and agin make sure grooves are alighned and push down until it feels it is seated. When done, give it a light pull to make sure it is secure and then you are done.
stripped agitator, would not move during wash cycle
drilled off top plate of agitator to gain access ot bolt, removed bolt, removed agitator, replaced coupler and new bolt, snapped in place new agitator.
Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while moving belt so it is properly seated on pulley.
Actually putting on a knob is self-explanatory. But wanted to say your company had the best price and reaction (delivery time). Great job by PartSelect!
The washer kept overflowing and flooding the garage every time we did a load of laundry
Instead of calling a repair man, we decided to look up the problem on the internet. We found that other people had the same problem on a website such as this. We narrowed it down to 2 parts. I opened up the panel on the washer where all the controls are (only 4 screws). Inside the panel was a diagram of the washer. We thought it would most likey be the Water level Pressure Switch. I found the part right away and removed it, I removed two connectors. It was really easy. We ordered the part online and it came really quick (within two days). I installed the new part(Water level pressure switch) and tested it. The washer worked perfect and did not overflow. We tested it again with a load of laundry. Everything was good. We saved a lot of time and money by fixing it ourselves. We did not have to wait around all day for a repair man and the part was under $30.00. I am happy the way it all turned out.
First I removed the agitator with a belt. Then I removed the nut with a wrench. The Agitator coupli was smooth on the inside so I knew that was the problem. I got the new part, slid it into place. Tightened the new bolt and replaced the Agitator component with a quick push downwards. Easy!
Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..ready to run.
Part Select inclusion of parts diagram helped determine which part was broken, and how to disassemble just what was necessary. I was planning to open up the control panel to get inside, which was not necessary. Assembly was simple for the same reason. Sometimes, it does help to read the "manual" first....
I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)
Unplugged washer. Removed four screws on the top panel, unplugged and removed old water level pressure switch (which was visually broken), replaced with new part, put the top panel back on, re-connected power, and tested to make sure that the washer would now fill to Extra-Large. Worked!
Popped the front off the washer by placing a towel under the screwdriver to prevent chipping the paint. Had to spent almost 45 minutes soaking up water that had leaked from pump. Must have been leaking for some time before enough leaked under washer and became visible, because there was a lot of rust build up. (1).Removed old pump by first un-pluging washer and them removing (2) connecting wires from pump. (3).Next use nut driver to loosen flex hose from washer. (not from pump). Loosen spring clamp from discharge hose , and slide up. (4) Using nut driver I removed (2) hex screws that held pump to frame, then removed pump and motor assembly. (5). Mopped up water with large (old) bath towels (6). Used hair dryer to dry area. (7). Used wire brush to brush away surface rust. then used small shop vacuum to remove this surface rust. (8). Used small brush to paint white rust-olem paint on rusted areas, used hair dryer again to help paint to dry, then gave it a second coat and again helped it dry. (9). I then removed flex hose from old pump assembly, checked it for cracks and finding none I attached it to new pump with existing spring clamp. (10). I then put pump assembly back inside washer, but did not attach with hex screws yet. (11). Re-attached the drain hose by sliding the spring clamp back down, making sure it is around the hose and discharge spout. (12). Reattach the flex hose to washer discharge spout. (13). Screw new pump and motor assembly unto newly painted frame. (14). Re-attach (2) wires to pump and motor assembly. (15). Plug washer back in and try filling it with some water, letting it go into the drain cycle to check for leaks. NOTE: You don't have to go through and entire wash cycle. Just use the dial to put some water in then move it to drain and /or spin to get the new pump and motor assembly going. I did this a couple of times and then did an entire load of clothes to ensure there were no leaks. After I was sure there were no leaks, I simply popped the front panel back on. My part cost a total of $64.00 including shipping, and it took me about 1 hour of my time. I checked with my local GE dealer and his cost would have been $98.00 for the part, and $85.00 for labor for a total of $183.00. I AM VERY HAPPY. Oh bye the way I had my part within 3 days of the order and that was with regular shipping. I will always use Parts Select from now on.
