Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Support stude for both vegetable crispers broken off
Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.
None of this was obvious - an online tip from another member was invaluable.
My grandkids broke the water dispenser in the refrigerator door.
The repair was easy. It just required a little time and patience. There are about a half dozen screws to remove and three of them are very small. I woild suggest a phillips head screwdriver with a magnetic tip for the small screws. They can easly fall into the control unit and be hidden. If they happen to fall, a small pen-type magnet that is expandable will make it easy to retrieve. I used a small set of needle-nose pliers to replace the small metal plates over the plastic pins that hold the water actuator in place. If your are careful, this repair can be done without disconnecting any of the electrical wiring.
Water was leaking from the valve/pump for the icemaker
Remove the screws that hold the old valve to the side of the refrigerator. Next, detach each plastic tube and attach that tube to the same place on the new valve, and repeat (there are many valves). Afterward, I realized that many of the plastic tubes had become brittle and had mineral deposits, so I bought additional tubing for ice makers and replaced each tube, one at a time.
It was very simple-it is just an insert glass shelf above the vegetable drawers. But, it was fairly easy to identify on your website and delivered in about two days.
After a power outage my refrigerator went warm & the freezer was cool.
I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.
Pull refrigerator from wall and disconnect the water line and unplug the power.
On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.
Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..
Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.
Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.
In about an hour you should have ice filling the bin. Enjoy!
First I removed the cover for the filter.(long nut driver) then the two screws holding the filter housing, held the retaining plungers in, and removed the filter housing. Then reversed the process and put it all back together. Simple.
It was a dreary day, too cold to be outside so I decided to tackle this repair. The first problem was one of the three screws holding the dispenser to the door was rusted in and would not come out. If I was smart I would have stopped there, but in the spirit of Tim the Toolman I found a way to work around it. I was able to get the panel off and disconnect the plug in wires and twist it to the side. The actual change of the paddle was a breeze- three screws and it was done. I turned the front section back into place, connected the wires and proceeded to replace the two remaining screws. All of a sudden the ice diispenser kicked in! First in the crushed mode then in the cube mode. You would be amazed how much ice the dispenser actually holds! I was trying to take screws out to disconnect the wires and catch ice at the same time not; an easy task. Once I had all the ice picked up I tried again and all seemed fine-the chilled water even dispensed again. Problem solved? Only until there was ice in the dispenser again and it decided to start dispensing on its own again. This time I learned and unplugged the appliance from the wall. I took everything apart again and disconnected the wires from the control panel and reassembled without reconnecting it. The repair company will be coming out next week to fix. Hopefully what would have been an easy fix will not become an expensive repair. It was one of those times I should have followed my gut when I ran into the first obstacle. I'll let you know the outcome when the professionals do their work.
I unscrewed the cover, took out old filter, put in new filter and replaced cover. End of story. Oh...don't forget to turn off the incoming water supply.
Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.
A 2" x 4" section on the bottom of the ice container bucket broke out.
Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.
