Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Lift up on the water filter door to open. Pull out the old filter while noticing the arrow pointing up on the filter. Pull off the green caps on the new filter and pop the new filter in with the arrow pointing up as on the old filter. Push in until the filter snaps into place. Close the filter door. Push reset on the water filter button on the freezer door to reset. Very easy!
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .
I measured the part then looked for a similar switch that might work. I was so happy to find the exact part we needed for our 24 year old refridgerator!! I was so impressed with your slection of parts and best of all I had the part in 2 days! You are in my "favorites" just in case I need you again!
We purchased the refrigerator new - but we wanted an extra door shelf bin for more dooor storage.
We ordered the bin and it arrived on time. HOWEVER - the plastic bin was broken in two areas. There was NO protective padding on the bin - just a simple plastic bag and then shoved into a box. We called customer service and the agent sent out a new one and we requested that this one be given better protective padding. She also refunded the first one as well as shipping costs. HOWEVER, when the 2nd bin arrived there was no padding but at least it was not broken!
Perhaps the shipping department needs to learn about Bubble Wrap - there really is no excuse for these plastic bins not to be protected..
Checked the water line from the wall to the supply port of the inlet valve and it was suppling water but no water beyond the water inlet valve, So I ordered a new inlet valve and installed, and it fixed the problem. Inlet valve supplies water to the ice maker and water dispenser filter housing. Partselect videos and you tube installation videos very helpful. Partselect troubleshooting guide also very helpful. Great company
Steps to replace Whirlpool evaporator fan motor 1. Watch numerous DIY Youtube videos 2. Move frozen food to refrigerator section, close refrigerator door 3. Cut power to refrigerator 4. Remove all shelves and bins in freezer section 5. Back panel has two parts, a top and a bottom section 6. Unclip small shroud covering screw bolt in upper left corner holding top panel. Remove screw bolt 7. Gently pull and work top panel out 8. Remove screw bolts from all four corners in lower panel and remove bottom panel 9. Verify power has been turned off 10. Unclip grounding wire 11. Unclip evaporator fan motor from power 12. Remove whole cradle holding evaporator fan motor. Note orientation of cradle. Fan blade is slightly angled toward the back of freezer. In other models, the cradle may not be removeable. 13. Remove plastic fan with firm pull 14. Unclip bottom brace to remove evaporator fan motor 15. Replace old grommets in bottom brace and on top of evaporator fan motor with the new grommets 16. Install new evaporator in cradle and clip-in the bottom brace 17. Install new fan blade on motor 18. Place cradle with new evaporator fan motor back in freezer 19. Reclip power and ground wire 20. Turn on power and test if working correctly 21. Turn off power 22. Complete steps from 8 to 2 in reverse
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced. reassembled the pieces.
Removed ice bucket and discovered the auger drum was broken.
After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.
Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.
Works great now, crushed and cubed ice dispenses thru the door like new.