Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher would not fill with water.
After doing some research in a repair book I decided to take a stab with a water inlet valve. With expedited shipping I ordered the part and within three days it was delivered. I installed it and the dishwasher seemed like it was trying to fill but still would not. After much cocnsternation I turned the water supply valve to the dishwasher a partial turn to close and I felt the water rush through the valve and the dishwasher then filled. Apparently the shut off valve must have been clogged plus it now leaked. I then replaced the shutoff valve and the copper pipe to the water inlet valve with flexible 3/8" tubing and the dishwasher thus far is running fine without leaks.
Upper nozzle "spinner" had degraded to the point where it no longer worked
The only difficult part was taking out (relatively easy) and returning (hard) the clips from the rails. This required bending the end of the metal rails with pliers. Otherwise the dishrack just rolled in with no issues.
The spinner is somewhat lower than the one it is replacing, making the clearance over items in the lower rack to be serviceable but marginal.
Water was not being sprayed thru the arms. I opened the dishwasher, removed/unscrewed the spray arms and wash impeller (black plastic wheel that directs the water) and then noticed that the part below the wash impeller had broken into pieces. There was only a metal ring and it was supposed to have a spring attached to it. I replaced the ring/spring below the wash impeller using the part from the Drain and Wash impeller kit. The dishwasher works great now.
It was my first mechanical fix. Use the web to diagnose, find the specs of the appliance and use common sense and you can do it yourself too.
By the way, the parts from this site arrived the next day.
The original rinse cap fell of and was damaged by heat
We couldn't find the model # on the web site and took a chance ordering the rinse cap for other models of that brand. When it arrived within a few days,it was simply a matter of pushing the new rinse cap into position. The replacement was of higher quality than the original. Although the price seemed a little high, it enabled me to use a rinse again. We are very pleased.
Replaced both "tracks" and the "wheels" . Now it's like new....!! My wife is so happy
Removed the track end caps from the tracks so I could pull out the tracks. Removed the upper wash rack that holds dishes. Only by removing this rack can the wheels be replaced, if I tried to replace them with the rack attached to the dishwasher I had to bend forward painfully. Replace the old rales with new ones. Attach new wheels to the upper rack in such a way as to allow the rack to roll inside the new rales. Replace the end caps. Hope it lasts another 10 years
First turned off the power at the breaker box. I removed the screws on the inside of the dishwasher, then took off the front touch pad control panel. Removed the old fuse, tested it, orderd a new one. Left the DW dismantled while I waited for the new part. Then put it all back together. I have also replaced the latch on this same DW, but they were both pretty easy.
Rubber hose disconnected and accidentally thrown away
This part is different than the original but works great. I used Geronimo's instructions, but cut the ring (see below) so I didn't have to glue it back together.
1-remove upper rack by removing holding clips.
2-remove old assembly from Rack
3-Use exacto knife to cut old ring guide at top between 2 hooks to accommodate new style (one solid plastic piece). No need to re-glue since the hooks hold it up okay.
Valve was leaking from plastic after water line change
Turned of water and unplugged the dishwasher. Disconnected the incoming water line. Drained on to the floor (have paper towels ready) Disconnected the electrical feed wire. Disconnected the rubber hose. Unscrewed screw holding the fixture to the frame. Took off the brass elbow from the old part. Put pipedope around it and screwed into new part (carefully, so as to not crack plastic again). Attached part back to frame. Attached water lines. Turned on water, plugged it in and ran dishwasher looking for leaks. No problem.
The spray arm snapped off from the mounting bracket.
First of all, we were very impressed with the ease of finding the parts, the ordering, and the velocity in which the parts were shipped. We received them the next day. I had to remove one of the screws from the old kit, since the new one only came with one. I looked at the diagram on the website of the assembly, and also remembered what the assembly looked like before I took it apart. The first time I tried it, I could not get the spray arm to spin without hitting the dishwasher rack. Since I had ran out of time, I had to wait until the next day. Once I started, I realized that I had the mounting bracket on backwards. Once I turned it around, I tightened the screws, and it was done within 5 minutes.
AIR INLET GASKET Had to pull dishwaher out, using instructions sent with part, turn it 1/4 turn counter clockwise, tap with screwdriver and hammer and it came right off. Put the new one on. It was kinda hard to get it to turn the last little bit, I had to use a screw driver and hammer to make it twist that last little bit.
I unscrewed the old water inlet valve from the frame of the dishwasher so that I could manuever my hand around to the backside where the rubber hose was connected. That was the easy part. I then had trouble holding the old valve while trying to unscrew the hot water copper tubing so I screwed it back on the frame. My dishwasher is close to 18 years old and I think that was part of the problem. After soaking in WD40, I finally got the valve out. Then I had to remove the "L" shaped connector to put on the new valve. Everything went back together a lot faster and it's like I have a new dishwasher again. By the way, I am a 53 year old female so that may be why it took me so long.
Removed dishwasher, take to garage, removed lower rack to gain access to top of motor unit. Used star socket wrench to remove upper screws holding top of unit in. Disconnect wires, drain tube and counter weight. pulled motor unit out from inside dishwasher and placed on bench. Proceeded to disassemble motor. Some things were obvious, others not so. replaced old worn out parts with new, used a little lube (Vaseline) in places to assist in getting seals back in place. Instructions were of little help need to pay close attention when tearing unit apart. Reassembled with new seals, installed motor and re-installed dishwasher...NO LEAKS!! Wife and I happy.
The dishrack fits perfectly in our 10 yr old KitchenAid dishwasher. Took a little while installing the wheels and 3 rows of tines that were not in place as instruction sheet was a bit vague. Our old rack had had several tines rust off, and recently learned that we should be using liquid detergent as the powder is like a sandblasting agent over time. Also we didn't get a knife/fork basket with the rack; however, old one fit okay.