Two of the four small nylon/plastic tabs on the adjusters that support the top rack on the rack slides, broke off (one on each side).
Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.
As practice, I took one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.
When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.
Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit
Kids loved to make squeaky sounds opening and closing the doors, finally snapped the door balance link on one side.
1) clear out the dishwasher 2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top 3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection 4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online 5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides 6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point 7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them 8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame 9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly 10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame 11) you've done it! 12) have a cuppa and do your second washer that hasn't failed yet - it will soon.
Left and right upper dish rack slide track started losing bearings, plastic holding left side completely fell apart and top rack fell down. The upper rack adjuster also broke as a result.
Make sure you have everything you need before you start. The upper rack adjuster broke when the left track failed and needed to be replaced. Although only the left side track failed, the right side would have soon enough.
This repair was fairly simple. First, toggle the circuit breaker off and turn off the water supply under the sink. Remove gray plastic covers to expose and remove Phillips head screws on each side of inner door frame then remove plastic kick plate before sliding the dishwasher out roughly 20”. The insulation needs to be folded back (tab release back bottom corner) to expose the four rack fasteners on each side. A small socket bit (I used a slow speed hand drill) makes quick work of removing old tracks but make sure one hand is inside on the track to catch what’s left of it. Replace both tracks (the second will fail) arrow pointing up using the fasteners you removed. Reset the insulation and make sure water, drain and electrical connectors are all in good order before sliding dishwasher back and fastening side frame screws to adjoining cabinets (tip: use painter’s tape or similar to keep screw head connected to screwdriver). Replace plastic caps and the kick plate. I had to replace the upper rack adjuster before reinstalling the upper rack on the new tracks. Check the bottom filter and reservoir for any plastic bits or ball bearings and remove them before turning power and water back on. Enjoy not having to hand wash dishes again. For me, about 40 minutes.
This was tricky, not so much the difficulty of the repair so much as finding the right instructions. There weren’t any on your website. YouTube videos were all over the place in terms of specific set ups. Eventually I found the right one. This would have been very easy and would have taken less than 15 minutes if I had the right instructions from the start. Most of my time was taken with searching for instructions.
Upper rack adjuster broke on one side. Detergent dispenser slide cover broke.
Replaced upper rack adjuster on both sides as these adjusters seem brittle due to heated drying over years. Followed YouTube video for repair. Very easy to fix.
Replaced the detergent dispenser on the door. Followed YouTube video with slight modification given moderate difference in model on video and my model. Relatively easy repair that takes a little bit of time.
unplug, disconnect water, remove all screws holding the machine in the cabinet. slide out the machine to access the 4 bolts hold the rail. Have a prop to hold basket in place as you remove old rail> Plastic clips front and back, hold the basket to the rail. Be careful not to break, not include with the replacement rail. If you are not handy with tools and no insight...hire it done
A mouse was chewed through the hose and ate part of it. Di
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!
Hardest part was figuring out how to release and remove upper rack as mine did not match the instructions. After that is was tricky but not overly difficult. The instructions on-line did not make sense, but it all was fairly intuitive process. Take some before pictures, lol. Dishwaswasher works great.