Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Glass door shattered completely!
The biggest mess is getting ALL the glass cleaned up, and especially clearing the channel that the new glass sits in. After that, very straightforward - Unscrew door from exterior frame, then handle from frame, then seat glass on lower rim and carefully refit the frame and handle to the glass and tighten everything back up - Good as new!
When we moved into our new home I discovered that the oven that came with the home did not have any racks in it. I ordered these racks because they said they were compatible with Hotpoint ovens. However, when the racks arrived they were just a tad too wide to easily slide in the oven. With a bit of force my husband was able to shove the racks in. Luckily I don't cook enough to care if they are moved again because I don't think they'll come out easily.
Element burst into flames, then oven wouldn't heat properly
First I shut off power to the unit. Then I removed the oven shelves. Next, I removed the two screws that hold the element in place using a socket ratchet. Then I carefully pulled the element out a few inches. I had some clothes pins with me because I read how some people had problems with the wire leads slipping back into the unit insulation. When the terminals and wire leads were exposed, I clamped the clothes pins on the wires between the leads and the oven wall so the wires could not be pulled back into the wall. Then I disconnected the wires from the old element. Next, I connected the new element to the wires, removed the clothes pins and gently nudge the element terminals back into the oven wall. Then I put the screws back to secure the element. Finally, I turn the power on and set the oven to 400 degrees. When I saw the element get red hot in a couple of minutes, I knew it was fixed. I've used it several times since then.
Used a pliers to remove old bake element (2 nuts that none of our socket set would fit). Removed the back panel with screwdriver. Unattached bake element from wires. Then removed old element and put new element in, pulled new element wires through back and reattached to range. Screwed back in the oven with the pliers. Closed up the back panel with the screws.
unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$
TURNED OFF CIRCUIT BREAKER FIRST. Pulled Stove from wall, Removed 5 screws to remove back plate. Unplugged 2 spade electrical connections. Unpluged temp. sensor plug. Opened oven door and removed 2 screws holding element to top of oven. removed screw holding temp probe to element. Installed the elment in the reverse order starting with the temp probe. when finished with install, I tested the unit before covering the back. I used a oven temp tester to make sure that when the element went out that the temp probe was not damaged. Everything checked out fine and I finished installing the back cover and putting stove in place. Cleaned up area and JOB DONE.
Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.
I unplugged the stove then took the oven racks out. Then I took a nutdriver and took out the 2 screws that held the Bake Element in place. Pulled the 2 prong's out of the oven and removed the wires from the tips. They pulled right off. Took out the new Bake Element and reversed the process. Attached the 2 wires put the 2 prong's back into the holes and screwed the 2 holding screws back in. Plugged the Stove back in and turned her on. Doing it myself saved me $150.00.
Turn off power to oven,remove two screws holding element in place,pull element forward approx. 1" and unplug wires,remove element. Install new element in reverse order of above.
After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a panel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.
The small burner inside the double burner shortd out.
The first thing was to watch U-Tube . The replacement burner was being replaced in a GE glass top range. Exter tools were required than depicted in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years