Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Basket was lost
Opened package from Parts Select. Removed Silverware basket from package. Opened Dishwasher. Inserted Silverware Basket in rack. Closed Dishwasher. Discarded shipping package. Told wife I fixed Dishwasher. Sat down & had a beer.
Motor was getting noisier every time we used the dishwasher. We knew it was just a matter of time before it totally quit.
The most difficult part was removing the dishwasher from below the counter. Once that was complete, I simply turned the washer onto it's front surface to access the pump easier. Simply disconnected the electrical connectors, loosened the three hose clamps holding the hoses to the pump. Lastly removed a stiff arm bracket holding the pump. Reversed the order to install the new one using a longer bracket provided with the new unit. Hooked up the electrical connections last and slid the washer back in place. The washer runs like new now and is not making noise. The replacement part was a perfect match.
front twoo rack rollers broken ,bottom rack roller broken
for the top rollers you must remove thethe end cap. this was easy ,i placed a block of wood on the outside .placed the punch on the inside where the channel is pushed in to hold cap on. smacked it till it was pushed out far enough to remove end cap. new rollers simply snap on. very easy,
Removed 4 screws in washer then removed cover. Then piston and nut assembly which just needs turned loose.Pull out and then,put new one back in,tighten up, put cover back on put 4 screws back in. Then unhooked water line, power cord, drain hose. Pull washer out and drained water out of system with drain hose. put a towel down to catch excess water. Loosen nut at end of drain hose with a pliers, remove flapper put new one back in tighten drain hose . Put washer back in hook water, power and drain hose. Run thourgh cycle and it should work much better.
took dishwasher out- put on table to work on-removed wire brace- disconected drain outlet- disconnected top drive seal- removed wire clip connector- removed motor unit---------------- installed new motor/drain unit--used new longer wire brac used adapter to connect electical leads- tightened clamps and bingo it worked and didnt' leak. good job on the supplying of all the necessary adapers.
First I removed the dishwasher from underneath the countertop and laid it on its back. I used a nut driver to remove the pump support wire and the two clamps holding the rubber connectors to the pump. It helped to hook the pump support wire in a hole in the left side of the frame and reconnect it to the pump to hold it up out of the way. I was able to remove the rubber connector by hand and unscrew it. To install the new rubber connector tightly, I slipped a piece of 2" PVC pipe (outside diameter is 2-3/8") inside the connector and tightened the clamp around the connector and PVC pipe. This allowed me to use the pipe to tighten the rubber connector. I reassembled the dishwasher pump and connections and put the dishwasher back into service
Went to www.PartSelect.com. Part was easy to locate online with GE model number and illustraion online. They shipped the parts in two days and I put the new parts on by hand. Saved a $135 service call from GE. One part came in broken from the factory. Upon calling customer servce, PartSelect sent out a replacement part the next day - no problem. Great service, would be happy to use again - Thank you!
Did the install a few days ago 4.25.11 and all went smoothly. The instructions that came with the kit were very straightforward and the diagrams were extremely helpful in locating brackets/hoses/connections. My dad thought he would just get down there and do it, but wasn't sure what to do. Using the directions with the kit, I had the motor and pump off in under 5 minutes. FOLLOW THE DIRECTIONS WITH THE KIT!
Some things to note: - Get some towels/cups/bowls, we had some water leaking from the dishwasher and hoses. - Be careful removing the dishwasher from the counters, go slow.
1. Shut off electricity 2. Shut off water. I just shut closed the line that went directly to the dishwasher. 3. Removed screws from bottom panel to expose motor and pump assembly. 4. Removed screws securing the dishwasher to the counters. 5. Slowly slid dishwasher from counter and rotated so door was facing the ground carefully to ensure wires/hoses were not pulled or crushed. 6. Removed screw from bottom of motor that was secured to the hanger. 7. Removed ground screw from bottom of motor. 8. Removed all wired connections from the motor and pump. 9. Loosened hose clamp securing the drain line and removed from motor. 10. Loosened 2x hose clamps securing the motor and pump assembly to dishwasher. 11. Ensured everything was clear and disconnected, and slowly removed motor and pump assembly from dishwasher. 12. Test fit new motor and pump assembly. 13. Reconnected 2x connections to the motor and pump. 14. Secured the ground wire to the motor and pump. 15. Slid motor and pump onto dishwasher and secured the 2x hose clamps. 16. Secured screw from the hanger cable to the motor and pump. 17. Reconnected water line to motor and pump, and tightened hose clamp. 18. Ensured all connections were made, hose clamps were tightened, and there were no extra connections. 19. Rotated dishwasher back onto feet. 20. Slowly slid dishwasher back into counters ensuring no cables or hoses were kinked or crushed. 21. Restored electricity and water to dishwasher, and then performed a quick test of one cycle to check for leeks. 22. Secured bottom panel and dishwasher to counters. 23. Enjoyed having a working dishwasher again!
The wheels on our dishwasher were mis-shapen and broken
It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!
The repair was easy. A couple turns of a screwdriver was all that was necessary to remove the rollers and slide assembly. The I simple installed the new rollers. Slid the slide into place between the rollers and then added the back caps to the slide. Replaced the rack rollers on the top basket and then slid it into position between the new slides. Once in place, I attached the end caps to the front of the slide. Simple and quick.
dishwasher leaking water when water went into drain
I read all the other repairs first to find out what I had to do. I then took front cover off the bottom of dishwasher. Identified the leak was coming from drain seal. I shut breaker off unpluged wires that were hooked to the drain valve sensor. removed the clip carfully as not to damage it. Removed srews that held down drain valve. removed the push on nut that holds drain seal in place. then removed old seal. I wiped down shaft to get ride of any corrosion and reinstalled new seal with deep socket and a srew driver. I installed new push on nut with another size socket. I fitted drain valve to shaft, used plyers to gently to pull shaft so I could put the c clip back onto grove on the shaft. reinstalled spring and plug wires back in turned breaker back on. I turned the dishwasher on and it did not leak. I was very happy that i did not have to take the dishwasher out. I did all repairs with everything still hooked up.
To remove the upper rack guide end caps, pull the inside flange gently to the rear, then twist the cap out of the track. Then the rollers come out easily, and replacing them involves merely snapping them in place over a rack frame part. Piece of cake! Roll the rack back into the guides, and replace the end caps. No tools needed!