Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Removed refrigerated items in door, (3) screws in top hinge bracket & lifted door off lower bracket. Turned door on side & removed lower hinge brkt. & old hinge pin. Replaced with new parts & reassembled door. Luckily I had some grease to apply to parts before reassembly.
First I removed the ice holder. Then I took the screw out of the side of the encloser, and pulled it out just a little and reached back and unplugged the harness. I had to remove the u-shaped piece off the little motor before it would go onto the new one. It was all very simple.
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Took my husband and son to remove the auger because it seemed to be frozen somewhat. After a little work, the auger broke loose and the repair was a quick process. I thoroughly enjoy the fact that the part was correct and I my ice maker was fixed for very little money and I did not have to buy a new refrigerator! I was not sure that we could get the replacement part because we are not the original owner of the refrigerator. So it has some age, but still works strong!
Removed 6 screws to get at broken part. Had to remember the disassembly sequence to properly reassemble. The whole process was relatively simple. I saved about $125 which would have been the cost of a repairman coming to the house.
First I removed spill tray. It slipped right out. next I removed the front cover.it had 2 screws hidden by the spill tray. next were the 2 screws holding the selection slider.Under it is 3 more screws after removing them then the assembly will come lose from the refrigerator.Be careful you dont drop the ice door. unplug the assembly. Turn unit over and you will see the limit switch remove and replace it with 1 small phillips screw. remove and replace dispenser actuator pad.replace everything in reverse order.The ice door is the only thing a little tricky.still i replaced ours in about 10 mins.
Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY
ice maker kept on dripping water causing ice in the icee containergood compression to freeze in a block
ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.
The ring was cracked and it would not dispence ice.
I switched the ring and still had the same problem. What caused the Drive ring to crack was the Ice maker drive was cracked also, when it filled with water it would tip. The ice was not freezing completely and would cause the ice to build up and the auger was froze with ice or a big piece of ice would jam it. So I replaced the Ice Tray, it is working like new. I have to buy another ice tray as inventory, although I know inventory is bad but I never agreed with that theory.
Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.