Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
flapper for the ice dispenser would not close completely allowing frost to build up in the freezer ice dispensing compartment
I watched the video explaining how to do this and it was a snap. MY PROBLEM WAS COMPLETELY SOLVED. Partselect.com is a must for my household. I couldn't be happier!!!!!
Used ice pick on bottom of water/ice cover plate to pop it loose. Removed 4 phillips head screws to gain access to the solenoid. Removed and replaced solenoid. Reinstalled parts removed to gain access to the solenoid.
Removing the trim ring around the control panel is the hard part. Be sure to watch the video on how this is done. Follow the video instructions on how to remove the solenoid and you will not have any trouble.
Replace solenoid which controls the despenser door. It is usually rusted. The front panel snaps off easily. Then there are 4 screws for the panel. Once the panel is off, the solenoid is exposed. There are 3 screws for the solenoid. You may want to spray dw40 on the screws if they are also rusted. Make sure you turn fridge off before performing this repair.
Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.
The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.
Changed out solenoid and plunger (comes as a kit). Repair was really easy and saved an expensive service call. Note: it is probably a good idea to get screws to go with the solenoid assy (qty 3) plus the screws that hold the dispenser plate to the door (qty 4). Mine were rusty due to the normally moist environment and had rusted, making their extraction more difficult than it had to be.
I watched the video on this site and read the comments here. Everything went as stated. I simply removed the front cover from the door, carefully pushing in the two plastic dimples to release the plastic piece. I used a very small screwdriver to get in the holes and pushed carefully while gently prying on the piece. It popped right out. I then carefully removed the three wire harnesses from the back of the cover. I then removed the four phillips screws that hold the cup pushing assembly on. I found this piece to be rather dirty/black moldy. I spent more time cleaning this with a toothbrush and soaking it than I did with the total repair of the solenoid, but I have much better piece of mind. I could now reach the solenoid, on the upper right hand corner. I removed the three screws and the solenoid was left hanging by the rusted top hook. I gently wiggled it off of the plastic arm that operates the flapper door. The new solenoid comes with the clip able to move freely and with no rust. Install the new solenoid in the same place and place the top hook onto the arm for the flapper door. Note, I WD40ed the screws and filed some of the rust off of the heads. I suggest ordering screws, like everybody says. But you can clean them up. I did this just in case I need to do this install again. The rest is just a matter of buttoning up everything. It is easy, don´t be intimidated. Anybody can do it, if you are the least bit handy and patient.
I followed the instructions that were posted on the partselect website and the video tutorial. It really was as simple as everyone had commented. Like others have noted, once the small tabs on the bottom of the faceplate were released, the cover came right off. Unplug the wire connectors, don't force them off. Remove the four screws and voila, there's the whole system laid out in front of you. It took me longer to clean up all of the gunk that had built up over the years. Once the new part was installed, everything went back together veray easily. The machine works like new again. Thanks partselect, you saved me some serious $$$.
I followed the easy video online that was mentioned in the paperwork that came with the part. The day before I replaced the flapper door for the ice chute and when I saw the rusted solenoid I immediately ordered that part which arrived the next day. I did not need to remove the border around the water/ice dispenser access area as shown in the video to install the parts. I did use a tiny screwdriver to press the little tabs on either side at the bottom of the front panel to release it to get to the parts. I was able to remove and replace the solenoid within minutes. And this was my first ever appliance repair attempt!
We removed the front panel by using a screwdriver underneath the panel to push three little tabs up to unlock the panel. Next we removed the mother board. Removed the old solenoid and put the new one on. It was very easy. We cleaned all he parts that were covered with mildew (yuck) and reassembeled all the parts. Very glad we found this source to do it ourselves. Will order more parts if needed from PartSelect.com
Pulled off fountain face plate. Removed four screws holding the plate in front of solenoid. Disconnected solenoid wires away from electronic board. Removed three screws holding solenoid arm.
Took about fifteen mins. to remove the three screws and slip out the solenoid and replace it. Only one electrical connection. Super easy to do. Unfortunately this did nothing to solve the problem. I still have no water. Nor did replacing the switch or the water valve solve the problem. I guess I'm done.
Ironically I did this today, as this email request came up asking how it went. I'm not a repairman, I'm a software engineer, and I can't thank this site enough for the step by step videos. With the video to help, this was a breeze, I was nervous as I had to empty all my freezer out onto the living room floor. Once that was done the repair took about 30 minutes. Thank you partselect!!!!! My second time doing business here, and I'll be coming back (well, if something breaks, so let's hope I don't have to).
