Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
washer wasn't spinning after rinsing but the motor was running
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Watched video from partselect and it was on the money. Removed a few screws and tilted the lid. (after unplugging). Pulled it out from wall and tilted machine to have access to bottom. Had grandson reach from underneath and pull the rods out and inserted the new ones. Work great now. My wife is happy and I saved about $600 because I didn't have to buy a new one.
I unscrewed the top panel of the washer. I lifted up the top and used the pint scrapper to loosen up the lid switch and slid it out. I pulled the switch wiring harness out of the rear top of the washer. I slid the new lid switch and wiring harness back through the opening and secured the switch in place. Screwed it back in place. Took less than 15 minutes. I followed the instructions on the video, easy peasy lemon squeezy.
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
The washer would not only shake, but sound like a mule was kicking the side of unit!
I watched the PartsSelect video. I was hoping for the tub with the slots in the tub mounts, but mine didn't have them, so I had to lay it down on its back. The only thing I did that was not in the video was I placed a 2" thick closed cell foam knee pad I had on hand between the tub and the back of the housing. When I laid it down, the tub was elevated by 2". This made reaching the two rear rods a little easy. It seems that there would be a more robust way to achieve the dampening affect, but I guess this is cost effective.
It's strange that I searched for my issue several times and only saw recommendations to level the washer. It was level. Then one day I ran across the suspension rod resolution. It didn't do it on every load, but after a year of my wife nagging me and threatening to get a new washer, I finally fixed it. The biggest issue is just logistics in a condo hallway and a little leaking water. I also replaced my hoses. Should be in good shape until the next thing.....
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.
When the washer would go into spin cycle it sounded like the drum was banging all four sides of the washer.
Unplugged from power, unhooked water lines.Then removed back cover and control panel and top set to the side. Rear rods very easy to do by yourself after those where done have help and tip it backwards and change out the front 2 then reassembled and hooked back up and tested. Everything worked like brand new !!!
The wash cycle made a loud grinding noise when it went from filling to wash.
I put the dial to drain and and pressed the pause button for 3 seconds and it drained. Unplugged the washer from the electrical outlet . Shut the hot and cold water off. Disconnected and drained them. Placed the washer on a soft mat on front side exposing the back and bottom of the machine. Unscrew the metal cover with Philips head screw driver. Disconnect the drain hose to a bucket or small dish tub . Remove the belt cover with 5/8 ratchet or wrench. Using a ratchet or wrench remove the one bolt holding the clutch in place . Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) . Pull down on bottom gear after removing nut. Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart. Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear. Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Washer won’t go into spin cycle! Tries too but then stops
Replaced the drive belt and shift actuator but that did not fix the problem! So I ordered a transmission and this still did not fix it! I give up! Time to get a new washer!
