Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The middle tub would not come out
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack When it came out it was full of rust and grime - it would have never come out without what we did Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
The temperature sensor in the water mixing valve quit working. It would operate on manual, but not auto.
As with any repair job, the hardest part is getting started and figuring out how to take it apart. I first tried to remove the top, by prying up on it,( his has worked in the past). This only broke the plastic retaining clips. I then removed the two plastic covers on each end of the control panel, then the two screws that hold the front of the control panel down. and lastly slid the control panel forward and out of its slots. I then used a 5/16th nutdriver to remove the four screws from the back panel. Now I was able to pull the panel back away from the washer body enough to use needle nose pliers to to remove the four electrical plugs located on the mixing valve. I used a felt tip marker to identify the locations of each plug. I used a 1/4 nut driver to remove the one mounting screw that held the valve in place and removed the valve. When the new valve arrived, It took about 15 minutes to re-install the valve and put everything back together.
It was a really simple thing to do. Make sure to buy the agitator cam kit (a little piece broke when I was taking it apart). Take off the cover and then the nut that is underneath. Replace the agitator cam and that's it!!! Usually those agitators dog ears wear down with time so if the agitator assembly is not turning, check this first.
Removed the outside body of washer. Used 1/2 plywood between drum and wear pads to make space to pry out pads with screwdriver. Replaced suspension springs and tub spring (use waterproof grease on end of springs. Put washer back together and tested. Problem solved washer not walking all over floor anymore. Thanks for you help.
I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
14 of 36 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top agitator did not work
I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism. Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
1. Unplug washer 2.turn off water, remove hoses from washer.3. Remove back cover, Remove screw holding inlet valve, carefully remove modular wiring, noting which wire goes where. Discard old inlet valve. Install new part. Reverse the above directions for installation.
Followed the video. Removed the case and holder clips (not really needed) and replaced the springs. It did nothing to stop the problem and there are no more fixes.
Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.
Leaked, disassembly revealed it was the drive seal washer grommet. Drive block was also rusted out and frozen to the washer drum
Disassembled lower part found nothing wrong. Started disassembly from the top. Immediately ran into trouble not knowing exactly how the tub was anchored to the drive. Once I got down to the tube and drive block there was nothing I could do to go further. I guessed it was a press fit onto the drive, but there were many instructions and I couldn't be sure. Parts Select expanded drawing was the most useful tool; it was correct omitting a few details. Anyhow, cleaning out my garage I found one of my old gear pullers that I could ring to complete the disassembly. All the sudden I was in business, pulling the washer drum off the drive block and shaft, getting down to the leaky lower seal. A that point it was just a matter of cleaning everything up and buying all the rusted out parts to reassemble. I spent $150-200 on parts, but its completely rebuilt now and runs like a charm. Probably have around 20-50 hours all told, into the repair. Most of this was reading instructions, watching videos, and trying to figure out the rest (3). Doing the actual work spread over time until my wife and sons threatened to throw the thing out. Never. Once I decide I'm gonna do something, I do it. LOL!
Tipped the washer onto it's side, used pliers to loosen clamps on old hose. Removed outer drain hose from white plastic hose adapter on back of washer. Removed white hose adapter (snaps out of place) and old hose. Fed new hose through opening for white adapter, then snapped new adapter into place on back of machine. Put the new hose in place and replaced clamps. Sat washer back upright. No more leaking! It was easy and didn't take more than 15-20 minutes.
Removed the 4 screws and nuts to get the control panel, off. Took-off brass clips that hold the back on. Removed 2 bottom nuts and plastic clips on back of washer. Took the back partially off, and removed the water inlet valve and replaced it. Reversed the procedure to re-assemble.The valve may not have been deffective, since after inspection, the hot water inlet screen was clogged with gunk.
