Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws. Saved $150 on a service repair call.
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!
The part I ordered has 5 connections and the part to be replaced has 7 connections. I had to ask a friend who is expert in electrical wiring to help.
My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections. Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Dual burner would only work on high and only the large burner worked
Replaced the dual infinite switch behind the panel. The wires were easily matched, even though the switch looked a little different. Works perfectly now.
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
The original instructions were to replace burner and plug wires back in the same plug they came from. The problem is that the plug order had changed between parts. Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
Inner window on my Frigidaire electric stove oven cracked
On this website, I found an instruction manual for this stove. There were 2 pages about how to change the glass on the oven door, including diagrams. I'd also checked a generic youtube video on changing inner glass on oven doors too, although the hinges in the youtube demo weren't exactly like those in mine. I printed out the instructions, checked the oven door to make sure the hinges looked like those in the diagrams, set aside a couple of hours on a free day with no other distractions, and did the job. I just kept removing screws from the inside oven door, peeling back the layers of the onion, until I got to the innermost glass, which was cracked. Put the new glass in, put it back together. On youtube the guy said it would take 20 minutes. It took me about an hour. Saved a ton of money by doing it myself.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.