Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The original plastic door catch was broken
I removed the 2 screws holding the broken door catch in place, and attached the new door catch with them. The repair could not have been easier, and now the door works great.
Also, I ordered the part, and it arrived via FedEx the next day. That greatly exceeded my expectations!
Would go into high spin in regular wash settings .
(1) Removed top of washer . (2) Open washer door . (3) Removed the two screws holding the Door Lock Sw while holding the switch from inside the machine . (4) Lifted the switch up to remove wire harness one wire at a time and reconnect to new switch . Double checked work and reinstalled switch . (5) Run washer machine make sure everything is back working . I need to add that the washer door needed to be adjusted . The bottom of the door was kicked out . Washer is now working .
no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!
The door catch on the washer broke, and I had to epoxy the broken catch to finish my laundry. I looked for the part online, and PartSelect not only had the part but had a photo of it as well. I was very impressed with how quickly the part arrived, and within 15 minutes the repair was complete. Thanks for having the photos and getting the part to us so quickly.
I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
The replacement of the Shock Absorber Kit was hampered on the right side by a metal box that was mounted just a little shorter than the bottom plastic pin. the deadblow hammer with the dowel worked with all the pins including the impeded pin and the top right pin which had to be removed at an angle. The replacement did not repair the washer - it is the tub bearing which went in a previous washer of a similar model about 4 years ago.
Ordered this part to replace a drain hose that had been cut short on the washer. Installation was straight-forward. Removed the two front screws to access the cabinet. Locate the drain hose and remove with a pair of pliers. Install the new part and attach the clamp with the pliers just like removal. Took about 15 minutes.
the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.
The door latch was broken from opening the door before the end of cycle release.
First I tried to unscrew the two screws holding the latch with a phillips screwdriver. When it wanted to slip, I took a closer look at the screw heads and saw they were square drive. I got the proper tool and removed the screws, replaced the latch and replaced the screws in a few minutes.
Washer was bouncing and emitted a banging noise only when on high speed spin
I watched the videos and replaced the shocks and suspension springs. This worked to stop the unit bouncing completely and cut the banging noise in half. Further diagnosis revealed a damaged drum and outer shell. The repair itself was very simple and didn't require special tools or skills. There is a tricky shock absorber locking pin on the right shock bottom position. There is a control box of some sort that prevents the complete removal of the pin without breaking it. On install, I simply pushed the pin through from the front. Ultimately, I ended up replacing the unit. However, I found the site to be extremely helpful. Great service.
Pulled the back off and it was right there. Hardest part was to get the belt all the way around the drive wheel on the washer tub. Found out that it wasn't just the belt. It is the shock absorbers that probably broke the belt, even though the belt was probably well over 15 years old. The bouncing and banging because of the absorbers being bad probably had something to do with the belt eventually breaking. Now, we need to replace the shock absorbers.A big thing to remember about the belt install....clean the drive wheel real good!!!
