Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.
The drum ice maker broke in half so it couldn't dependent the ice.
I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.
This is the second time I've had to replace the crisper cover, so I had that step mastered. As before, I took the glass from broken crisper cover and dropped it into new cover in seconds. Had to use a screwdriver to pry old crisper supports from the walls of the fridge. This was the only hassle. Popped new supports in, replaced crisper covers, and slid crisper drawers back into place. From now on, I'll have to be more careful about how much weight I put into crispers.
Took off Door on Refr. and unscrewed Doorstop, removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes including reattaching Door. A 10 year old can do it.
Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.
removed fan unit from frig and installed new motor and then replaced back in frig. No tools needed. need to unplug unit and take apart and put new motor in the unit and then plug back in.
We had to unhook & remove icemaker several times, thaw it out & reinstall, it would work for a day or two then overflow. Bought the new ice marker, replace it and it works great....
The top crisper drawer frame was cracked, it secures the glass top also.
Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.
It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!
Support stude for both vegetable crispers broken off
Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.
None of this was obvious - an online tip from another member was invaluable.