Washer Pumps

The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.

This drain pump for your washer is designed to remove the dirty water during and after the washing cycle. If your washer has water left in it after its washing cycle is over, or if your washer is experiencing leaks around the drain pump, the pump may be damaged or bad and in need of replacement. Ensure you remove and test your drain pump with a multimeter before replacing it. Replacing this pump will require some disassembly of your washer. This pump is sold individually, and does not come with any wire harness or other accessories.

This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.

The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is supposed to drain the water from the washer; if the water isn’t draining or if there is a leak, you may have a problem with your pump. You must replace this part if there is a blockage or clog. Although the symptoms may point to a malfunctioning drain pump, there could actually be a problem with one of the connecting hoses. This pump connected directly to the motor, and comes in white plastic. This replacement part features 1 direct drive water pump with 2 ports for water to pass through: a large one and a smaller one.

This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair of pliers. Make sure to disconnect power to the washer before beginning this repair.

This drain pump assembly is a genuine replacement part designed for select LG and Kenmore washing machines. It plays a critical role in removing water from the washer tub during the drain cycle, ensuring efficient water evacuation and proper cycle completion. Powered by an 85-watt, 120-volt motor, the pump is typically located near the drain hose at the bottom of the appliance. A failing pump may result in water remaining in the tub, incomplete draining, or unusual grinding or knocking noises during operation. Replacing the pump restores proper drainage and helps prevent water damage or cycle interruptions. Installation should be performed with the washer unplugged and may require basic tools and moderate repair experience.

This washer drain pump is a genuine replacement component designed for select front-load washing machines from Whirlpool, Maytag, Kenmore, and affiliated brands. It plays a vital role in the wash cycle by efficiently removing water from the drum, helping to prevent leaks and ensure proper drainage. A malfunctioning pump may result in slow or incomplete draining, water leakage, or error codes related to pump failure. This part is engineered for durability and reliable performance, and replacing it can restore optimal function to your appliance. Compatibility should be confirmed using your washer’s model number prior to installation.

This drain pump is specially designed to fit in top load washing machines. It is responsible for removing water from the washer tub during the drain cycle and directing it to the household plumbing system through the drain hose. If you notice longer draining times, grinding or rattling sounds, or standing water in the tub at the end of a cycle, the drain pump is likely faulty. This may be due to several reasons such as normal aging, wiring problems or physical damage. It is also common for the drain pump to become clogged with small items such as coins or buttons.

The washer drain pump assembly is an essential component that ensures efficient water removal during the draining portion of the wash cycle. Crafted for durability and reliability, it restores optimal performance to your appliance. The assembly is designed to fit seamlessly into your washing machine and may include multiple parts, so consult your washer’s parts diagram for a comprehensive list of included components. Installation is straightforward but requires unplugging the washer and wearing protective gloves for safety. Always confirm compatibility with your washer model before purchasing to avoid fitment issues. This replacement drain pump assembly is in stock and ready for prompt shipment, ensuring minimal downtime and a quick return to optimal washing performance.

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.