Make sure you haven't got the discount earlier.
![Customer Service Representative](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/csr-partdetail.jpg)
TUB SEAL WH02X10362
Fits your GTW810SSJ1WS!
Rated by 1 customer
Very Difficult
More than 2 hours
Ratings submitted by customers like you who bought this part.
Fits your GTW810SSJ1WS!
PartSelect Number PS8757008
Manufacturer Part Number WH02X10362
Manufactured by
GE
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer.
This part works with the following products:
General Electric.
Customer Repair Stories
Average Repair Rating: 1.0 / 5.0, 1 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Tub Seal Replacement - Direct Drive with Detergent/Fabric Softener Despensing
This procedure was completely different from any other Tub Seal I've done and in my opinion needs 2 people. The first thing to note is that this seal must be removed from the bottom of the outer tub. Also, the top of this machine does not hinge in back. The typical clips are in front, but the back has 2 screws that must be removed. Since
... Read more
the wiring was too involved to completely separate the top from the base, I had to improvise a stand to hold the top while the rest of the process was completed - keep slack on all remaining connected wires. The motor, clutch and bearing plate must be removed from the bottom in order to access the Tub Seal. Below are the steps I did to complete the process:
- Remove Control Panel Cover (rear)
- Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well)
- Remove Pressure Switch
- Disconnect Detergent and Softener dispense hoses from Machine Top
- Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires.
- Remove Tub Cover
- Remove Impeller (Agitator) from inside tub.
- Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact)
- Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall)
- Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal.
- Replace Cross bar to keep unit stable
- Lay machine on its side - use care not stretch or pull any wires.
- Remove motor, (Rotor and Stator)
- Remove Clutch and wires
- Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate
- Remove all screws securing Bearing Plate to Outer Tub
- Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care)
- Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap)
- Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires.
- During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
- Remove Control Panel Cover (rear)
- Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well)
- Remove Pressure Switch
- Disconnect Detergent and Softener dispense hoses from Machine Top
- Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires.
- Remove Tub Cover
- Remove Impeller (Agitator) from inside tub.
- Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact)
- Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall)
- Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal.
- Replace Cross bar to keep unit stable
- Lay machine on its side - use care not stretch or pull any wires.
- Remove motor, (Rotor and Stator)
- Remove Clutch and wires
- Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate
- Remove all screws securing Bearing Plate to Outer Tub
- Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care)
- Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap)
- Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires.
- During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
Read less
-
Greg from SPRING CITY, TN
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kevin
September 10, 2019
Water running out of rotor housing.
For model number GTWS8450D0WS
Hi Kevin,
Thank you for your question. If there is water leaking from the rotor housing, the water may becoming from the tub and you will need to inspect the tub and the parts underneath it to see which part is causing the issue. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Gemma
July 12, 2022
We need a tub seal for the above washing machine model.
For model number Mod.GTW180SCJ0WW
Hi Gemma,
Thank you for your question. The part number listed under your model number for the tub seal is PS4704237. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
![NUT HUB – Part Number: WH02X10363](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/8757009-1-N-GE-WH02X10363-NUT-HUB.jpg)
![WASHER HUB – Part Number: WH02X10364](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/8757010-1-N-GE-WH02X10364-WASHER-HUB.jpg)
![Produce Preserver Filter – Part Number: W10346771A](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/3503014-1-N-Whirlpool-W10346771A-Produce-Preserver-Filter.jpg)
![Affresh Washing Machine Cleaner - 3 pack – Part Number: W10135699](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/1960673-1-N-Whirlpool-W10135699-Affresh-Washing-Machine-Cleaner-3-pack.jpg)
![Affresh Dishwasher Cleaner Tablets - 6 – Part Number: W10549851](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/12345667-1-N-Whirlpool-W10549851-Affresh-Dishwasher-Cleaner-Tablets-6.jpg)
![Affresh Cleaner – Part Number: W10282479](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/2367638-1-N-Whirlpool-W10282479-Affresh-Cleaner.jpg)
![Cooktop Cleaner – Part Number: W10355051](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/3492527-1-N-Whirlpool-W10355051-Cooktop-Cleaner.jpg)
![Affresh Ice Machine Cleaner – Part Number: W11179302](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/12583750-1-N-Whirlpool-W11179302-Affresh-Ice-Machine-Cleaner.jpg)
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS8757008
Manufacturer Part Number: WH02X10362
Manufacturer Part Number: WH02X10362
Brand
Model Number
Description
Back to Top
![Customer Service Representative](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/csr-partdetail.jpg)
TUB SEAL
$
15.32
Special Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.