This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to your parts diagram for a complete list of parts included.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Pumps but will not spin | Spins slowly | Noisy
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Maytag, Kenmore, Amana.
Part# W10528947 replaces these:
AP5665171, W10396887, W10528947VP
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Annette
October 30, 2017
Does part 8 come with part 9 or do you have to order separately?
For model number mvwc555dwo
Hi Annette, Thank you for the question. When you order #8 PartSelect Number PS601209 Hub you will be shipped both Item #8 and #9, The Hub and Washer Drive Hub Retainer.Hope this helps!
30 people found this helpful.
Was this helpful?
Thank you for voting!
John
October 18, 2019
This part wears out every two to three months it is not because of overloading it is because of a bad design. The washer says it is heavy duty then why would you put a cheap part made of plastic on it! This part should be made of metal! My opinion Kenmore should recall the part and make a metal replacement part!!
For model number W10528947
Hello John, Thank you for contacting PartSelect. We believe this is a concern best addressed by the manufacturer. We are a parts distributor. We do not manufacture any units, parts, authorize substitutes, or fulfill warranty claims. Please contact your unit's manufacturer, directly.Hope this helps!
21 people found this helpful.
Was this helpful?
Thank you for voting!
LP
March 28, 2018
Is the replacement hub #8 made of metal or plastic?
For model number MVWX655DWO
Hello LP, thank you for your question. The part number HUB W10528947 is made of plastic. Good luck with your repair!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Heather
January 31, 2019
I replaced the screw that holds the wash plate a few months ago. Now the plate spins freely and the machine wont agitate properly...will the drive hub kit fix the problem or do i need a new wash plate? (the screw is tight)
For model number WTW5000DW0
Hi Heather,
Thank you for your question. If the washplate is spinning freely and the screw is tightly in place, it may be stripped. This usually occurs if the the washer is constantly overloaded. You will likely need a new washplate. I hope this helps. Thank you and have a great day!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Chuck
September 13, 2017
Will replacing the hub quiet down the noisy spin cycle?
For model number WTW4950XW3
Hi Chuck,
Thank you for your inquiry. There are a couple of parts that could cause your machine to be noisy during the spin cycle. You may want to check your clutch assembly, belt, and your suspension rods. These parts can wear and tear over time and may be the cause of the noise. Good luck with your repair.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Lori Strickland
January 9, 2019
My wash tub in the middle of machine is spinning so fast and throwing the clothes all around so it’s off balance. Will this fix the problem?? everything else seems to work well it is only 1 1/2 years old
For model number MVWX655DW1
Hello Lori, thank you for your question. We would recommend replacing the Drive Splutch Kit.part number W10721967, belt part number WPW10006384 and actuator part number W10913953 first. An issue with the hub kit is usually noise, or grinding or the tub doesn't spin during the spin cycle. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Jeanne
August 22, 2019
Not spinning out the water completely. Towels still very wet!
For model number MVWC4258W1
Hello Jeanne, Thank you for the question. I suggest checking the driver belt PartSelect Number PS11747978 to see if it has wear and has stretched out. If there is wear it may not be able to grip and spin fast enough on bigger loads. Hope this helps!
The machine wont spin, installed a new gear case (old one was striped at top and the hub was also stripped out. order new up hub did install new gear case. once new hub is installed should this be good to go or am i missing something else?
For model number mvwx655dw1
Hello David, Thank you for the question. If it is just the hub and gearcase that was damaged, this kit should fix the issue. When you order #8 PartSelect Number PS601209 Hub you will be shipped both Item #8 and #9, The Hub and Washer Drive Hub Retainer.Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
January 16, 2018
Will the basket having a little free play cause the washer to get out of balance? I am having a problem with it getting out of balance on the fast spin cycle then switching to a slower speed spin. I have replaced the spluch and belt. My only guess now is to replace the hub and retainer and/or the suspension top pivots.
For model number 110.25132410
Hi Mike,
Thank you for your question. If the washer is still out of balance and you have replaced the clutch and the belt, you will need to check the suspension rods and the suspension rod supports.
I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Lyn
August 6, 2018
The washer agitates but the drum doesn't turn during washing and spin, just agitater
For model number Mvwx655dw1
Hello Lyn, thank you for your question. There are a few parts we would recommend you check. The Drive belt, clutch, hub and actuator. Here is a like to these parts. I hope this helps!
https://www.partselect.com/AdvancedModelSymptoms.aspx?ModelNum=MVWX655DW1&mfgModelNum=&fkMfgID=1&ModelMasterID=868794&PID=26
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Hub had warn its grooved teeth off and washer wouldnt agitate
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed.
Allison from RICHFORD, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
27 of 33 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn't spin properly
Replaced the gears that were eaten up, the retainer and the actuated. All parts but the spring are plastic. Did all according to your instructions. Happy to report all went well. Washer is working again.
Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
Andrew from SYLVANIA, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the splines were worn out on the hub assembley
screw driver and a rachet and socket took it off and put the new one on . no problem follow the direction that comes with it .
Johnny from NORTH JUDSON, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
violent basket wobble
remove basket and replace drive hub kit
Keith from DUNBARTON, NH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wash plate spinning. Clothes not spun out.
Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 cheaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.
Remove the center cover with a screwdriver then loosen the 7/16 bolt with an impact driver socket ccw to remove completely biggest issue is removing bottom cover tried pick tools only thing that was succesful was some dawn dishsoap on the center bolt area to loosen enough to lift up the cover replace the hub part that had worn spline grooves remember to use blue loctite on the 7/16 bolt before re-installing cw to tighten bolt
Craig from CRARY, ND
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
During the Spin cycle the washer was noisy and moved around
I watched the video and did exactly what they said to do. It was really easy. The key to the success was in the parts that were mailed to me it had a separate piece of paper telling you to "reset" the washer after doing the repair. I missed this when I watched the video. That was a critical part of the repair which required no tools to accomplish. I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!
JOHN from HERNANDO, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no spin
reviewed video of repair and repaired now washer works as it should . thank you
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Pamela Q - April 27, 2022
Verified Purchase
part was exactly as ordered
Repaired washer and working great!
★★★★★
★★★★★
David R - April 21, 2022
Verified Purchase
Repair went well!
The part was a perfect fit!
★★★★★
★★★★★
John Y - February 9, 2022
Verified Purchase
Maintenance
I repaired my hub .it went out after six years.
★★★★★
★★★★★
Nelson V - January 22, 2022
Verified Purchase
Washer not spinning clothes
Perfect fix. Website, video, troubleshooting guide was amazing. Thank you guys for being an amazing help. A friend of mine’s washer broke down at the same time, by the time that the service person came out to fix it I already had my part and my washer was working. Also it was way cheaper.
★★★★★
★★★★★
Linda S - October 13, 2021
Verified Purchase
Worked Great
The website led me right to the part that was needed. Easy to install once we got the old part out. Works great.
★★★★★
★★★★★
Brent B - September 23, 2021
Verified Purchase
Great part
Part worked well and arrived quickly.
★★★★★
★★★★★
William S - August 14, 2021
Verified Purchase
Easy fix
This is the second one of these I bought in two years. The problem is that the splines on the hub are plastic and they wear away in no time.
★★★★★
★★★★★
KAREN S - July 12, 2021
Verified Purchase
Works great!
Great service and very fast delivery! The part was easy to install and it took less than 15 minutes to complete. My washer works great! I haven’t had any issues and it’s been about 4 months since I installed it.
★★★★★
★★★★★
Tonda D - December 28, 2020
Verified Purchase
Easy DIY
The part came in quickly and the repair was simple to complete.
★★★★★
★★★★★
Jacques M - October 21, 2020
Verified Purchase
Perfect fit, not too hard to replace
The parts were exact OEM replacements, easy to install. Getting the old wash plate (agitator) out was a bit of a booger. I removed the center cap with a screw driver, and the center bolt with a socket. I tried holding the wash plate up and tapping down on the bolt head after loosening it a few turns (per a YouTube video) but had no luck. I created a pair of pullers by taking apart a wire pants hanger, cutting it in half (at the top of the hook) and forming the hook area into a loop. I straightened out the rest of each side except for the little u-turn at the end. With the center bolt removed, I was able to slip the u-turn between the tub and the wash plate on both sides (left and right.) Then, using the loops as handles, I popped the wires up a few times, moved the wires 90 degrees and popped it some more. Eventually, the wash plate came loose.
To remove the drive hub, I tapped the tips of the retaining clip horizontally toward the opposite end of the clip, which loosened it. That made it easy enough to pry out with a screw driver. I backed out the screws carefully so as not to strip the heads, and the drive hub lifted out pretty easily.
If memory serves me, the new hub lines up only three ways, even though there are six screws. When you install the screws, turn each one in only a turn or two initially so that the hub seats evenly. It is manufactured in a way that you cannot just push it all the way down, but once you start the screws, the hub will slip into place and hold firm.
The wash plate just slips over the drive shaft. I cleaned most of the rust off before replacing it. IMPORTANT: Put a drop or two of thread locker on the bolt before reinstalling it. This will keep it from backing out.
With our Fix app model plate image recognition technology, we'll recommend the parts guaranteed to fit your appliance. Simply snap a photo, and we'll take care of the rest.
"I love love love this app. It's so nice to have useful information (receipts, manuals, parts lists, warranty info, pictures, etc.) on all of my household appliances and devices in one place."
You added to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
