Ask our experts a question about this part and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
July 31, 2018
How do I remove the panel in the top of this model to change water valve
For model number WRX988SIBM01
Hello David, Thank you for the question. On this Model the water valve is in the upper ceiling inside of the refrigerator. To access the valve. you will need to unplug the refrigerator to disconnect power. Next open both doors. Remove the top shelves. Remove the ice box fascia using a flat blade screwdriver and pull out bottom of fascia to release the upper tabs. If your ice box has a revised ice box fascia with a heater, you will need to disconnect the fascia heater wiring harness. Next remove the water filter. Using a ¼” nut driver remove the two screws from under the water filter door. Starting from the ice box side, place a flat head screw driver between the water reservoir cover and refrigerator liner creating a gap to place your hand between the two. Working from left to right, slide your hand between the water reservoir cover and refrigerator liner to release the snaps. Remove the water reservoir cover by sliding it forward and disconnect the LED lighting connector. This should expose the valve. Hope this helps!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Todd
November 25, 2017
How to remove the dual inlet water valve at the top of the refrigerator?
For model number wrf736sdam13
Hi Todd,
Thank you for your inquiry. There is a video on our website that you can reference on how to install the water inlet valve. You will find the video under part number PS3497634. I hope this helps. Thank you and have a great day!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Doug
May 30, 2019
How do i remove the top panel to gain access to the secondary valve and plumbing to find the source of a water leak?
For model number KRMF706ESS
Hello Doug, thank you for your question. Open the doors and remove the shelving from the right side of the fridge compartments. Depress the tab on the cover then bend the cover outward to remove. Then use a flat head screw driver to depress the tabs to release the lower access panel. Release the center retaining clip to remove the upper access panel and then you will have access to the valve. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bernie
December 31, 2019
I have replaced both the icemaker and the water valves and i have the same results. I can dispense water but the icemaker does not fill with water. I have bought and replaced the following parts. W10341329 valve, and w10764668 icemaker. I'm starting to think those items may not of been an issue. Can you help
For model number KFIS29BBMS03
Hello Bernie and thank you for writing.
You should check the tubing and see if you might have a hairline crack somewhere. We hope this helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jim
September 18, 2023
Does this part failure cause water to run continuously into the icemaker?
For model number KRFF507HBS00
Hi Jim, thank you for reaching out. The water inlet valve requires a minimum of 20 psi to shut off properly. If the water pressure is too low, the valve may not close fully once the power is shut off. As a result, the valve will leak water into the ice maker and cause the ice maker to overflow. Check the water pressure to determine if it is at least 20 psi. If the water pressure is sufficient, the water inlet valve is likely defective. The valve may not shut off all the way or may be stuck open, causing water to leak through the valve. If the water pressure is sufficient, but the ice maker is still overflowing, replace the water inlet valve, part number PS11753251. Good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Kevin
December 28, 2023
ice maker quit working ( no ice being dumped ) last couple of batches seemed slightly "melted" looking...any suggestions?
For model number wrf736sdam14
Hello Kevin, thank you for reaching out. Based on our understanding, the issue is most probably with the ice maker assembly, part number PS17215831. We would recommend replacing it to solve the problem. Glad to be of assistance!
The ice maker in the freezer had a drip causing the rubber boot on the filler to freeze and split.
For model number WRF767SDHZ01
Hello Shane, thank you for contacting us. Based on our understanding of the issue, we would suggest checking the water inlet valve, part number PS11753251, to fix the issue. We hope this helps.
Was this helpful?
Thank you for voting!
Ray
April 12, 2024
Door water dispenser pressure is very week. Is very slow to fill a glass.
For model number wrx988sibm00
Hi Ray, thank you for reaching out. Based on our understanding, we would suggest checking the water inlet valve first. Make sure that the water inlet valve screens are not clogged. If it is fine, the issue could be with the water filter, part number PS11722126. You may need to replace it to fix the issue. We hope this solves your problem!
Hello, I have no water in my fridge. The valve does not open when I operate. The switch in the door works because the light opens and the display shows the volume of water, it remains at 0 oz.
For model number KFIV29PCMS02
Hello Alexandre, Thank you for the question. If the Valve is not opening to release water, we suggest having it replaced. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.