Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.
I pried the relay from compressor with small screwdriver, cut and replaced burnt wire going to relay,pushed new relay on compressor and wires unfortunately it did not fix the problem.
I replaced the water solenoid kit,control board and a broken dispenser assembly crank.My repair went well, parts came on time,I watched an R&R video on youtube provided by PartSelect and finished the job in ten minutes. I am one happy do it yourself-er customer.
The solenoid that opens the ice chute would fire, but the ice auger would not turn in either direction. I verified that the motor was OK by running 120 V to it directly. Changing out the "timer board" was a 15 minute job and did the trick. Ice galore!
Icemaker waterline leaking inside by the grommet where the water line comes in the refrigerator . First removed the water line from grommet . Then removed grommet by hand from the fridge. Last, reversed prodedure.
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
I took the ice maker tray out and dumped the ice and then removed 4 screws to take the plastic front off the drawer. I then took 4 more screws out to remove auger assembly. I could now unscrew the broken nut and replace it with the new one and put the snap ring and washer back in place and then put everything back together. Done Had I had my lathe running at the time I would have made this part out of aluminum instead of the new one and original that is out of plastic which is why it did not last.
Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.
I received the part after doing what was instructed by process of elimination for the problem.I installed it and it still didn't work. I took the part out and called to return it but was told i couldn't because it was now a used part and your company only sells knew parts. Now, I have a circuit board that I have no use for.
Ice maker arm disconnected from frame causing problems.
The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.
Disassembled ice-maker, noting what screws went where, what direction ice release control arm pointed, and noting how the control arm spring was mounted. The door assembly comes off first followed by the circular assembly that houses the ice door and last grinding arms. It is quite easy see how it comes apart as you look at the screws. Remove the screw holding the back end of the control arm and note the spring position. The control arm needs to be turned to line up notches to pull it thru a faceplate hole while rotating the arm about the "U" that is on the outside of the faceplate in the door housing. There is a retaining clip holding the rotating impeller to remove to complete the dis-assembly. Use vinegar to clean rust out of bin and other parts around the faceplate. Assemble the unit in the reverse order to complete the job.
Ice maker had to be removed from refrigerator, solenoid removed with four screws. Fairly easy repair and the part was delivered the day after it was ordered.. superfast repair.