Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
1. Turn off water supply. 2. Remove the metal toe kick plate/insulation at the bottom of the dishwasher. 3. Remove hose to supply valve. 4. Take electrical plug off old valve. 5. Remove float valve because it was mounted it right in the way of the 2 screws on the inlet valve bracket. 6. Remove those 2 screws now you can get to them, and move the inlet valve to one side so you can get to the hose clamp for the rubber hose out of the valve going to the dishwasher. 7, Take the old valve and bracket out, mount new valve on the bracket, crawl back down on the floor, reinstall rubber hose and bracket, and float valve and finally inlet hose. 8. Turn water on. Check hose connections for leaks. Yep, outlet hose didn't clamp enough now, allowing a drip. 9. Repeat the whole process AGAIN. Replace little clamp with a REAL hose clamp, reinstall the thing again. No leak this time. 10. Test run dishwasher thru a cycle. Check again for leaks at hose connections. OK ? Reinstall insulation pieces and toe kick plate.
delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.
The rollers on the bottom rack of my GE Monogram Dishwasher all broke and melted so opening and closing the rack was extremely difficult!
It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!
The plastic wheels kept falling off the bottom rack of the dishwasher
The old wheels and attachment brackets were easily removed since they were always falling off. I ordered all new brackets and wheels, but it turns out I didn't need new wheels. If your original wheels are in good condition, they are the same size as the new ones and fit the new brackets. The new attachment brackets are built differently than the ones that came with the dishwasher, but (a good thing considering the originals only lasted 1 1/2 years). The new brackets and wheels snapped together and snapped into place on the dishwasher in minutes--no tools were needed. It took longer to cut the parts out of the packaging than to install them. The bottom rack now rolls out like it did when it was brand new. Definitely worth the few dollars in parts.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Simply remove broken wheels and clip on replacements. No tools are necessary for this fix and the replacement was inexpensive and easy to install. The kit worked beautifully.
Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.